#mock-up

[carsthatnevermadeitetc]

Skink Buggy, 1971. A 6-wheel ATV to be powered by a mid-mounted rotary engine, designed by Justin L. Dantzler, Clark Valentine and John A. Vernon. Unfortunately their design study didn't progress past this full-size mock-up. A Skink is a small prairie lizard

[roguetelemetry]

Nostromo concept sketches and early stage model. The first sketch clearly shows how the Nostromo is towing the refinery rig.

[vt-scribbles]

All Eyes on You

[lonestarflight]

Grumman mockup for the Apollo Lunar Module.

Date: October 9, 1964

Grumman Aircraft Corporation photo: LPS 340-837, LPS 340-842

[xfand0mfr34kx]

pen doodle dump :P

[ourstolenlullabiess]

“Sagittarius”, an album concept by Taylor Swift, featuring the hit song “In Orbit” feat. Halsey.

[tdad]

chris yo mama - ari

[thewalkingmeepa]

Happy #Pride

Commission for @stupidsexycopshows for her fic Like, Comment and Subscribe!

[sketchmii]

A Mysterious Mage blocks Arles final destination, demanding her to, “Leave…”

✨HAPPY BIRTHDAY @mermaidsscale !✨

This is a Puyo/Madou Monogatari Persona I made for my good friend years ago that I recently revisited to make this gift! Also the first time coloring them too!

Also I would like to a warm thank you to my sweetie, @kiwwy101 for suggesting some of the color theming! Mainly to keep the primary color PURPLE !

Other than that, this was planned for YEARS actually. Originally going to be a Puyo Puyo themed gift, but I changed it to Madou Monogatari because I liked the creepy atmosphere the PC-98 games had.

Hope you and everyone who’s a fan of this series enjoys this special piece I made for you!✨

[conformi]

Wolfgang Tillmans in Prinzessinnenstrasse 2, 10969 Berlin, PIN-UP MAGAZINE, ISSUE 32, SPRING/SUMMER 2022 VS Michelangelo Pistoletto, Labirinto e megafoni, Museum Boymans Van Beuningen, Rotterdam, Netherlands, 1969

[mockupcloud]

União Construtora | Visual Identity

Mockups used in this project ⚡ mockupcloud.com

Design by versattobrands.com

[carsthatnevermadeitetc]

Chevrolet Corvette XP-719, 1959. A mock-up for an experimental rear-engined Corvette designed by Carl Renner and Larry Shinoda (seen the fullsize rendering pic with engineer Ron Hill). This was the first known Corvette concept with anything other than a front mounted engine.

[frenreyhlvrai]

[stijlw]

'november' from scott king's how i'd sink american vogue, a work in 12 parts he did in 2006. digital print 27.5 x 20.5cm

[lonestarflight]

A mockup of a 12-man “Big G” spacecraft at the McDonnell Douglas factory. It was intended to provide large-capacity, all-purpose access to space and be a logistic spacecraft that would be used to resupply an orbiting space station.

Date: April 14, 1969

source, source, source, source, source, source, source, source, source

[dkettchen]

✂👖 updating y'all on my pants adventures 👖✂

I decided to try and make a wearable, full-length mock-up to test out my initial block pattern from the other week, thinking it was gonna be easy and chill and merely a matter of adding the like pockets and stuff, right, it couldn't possibly be that far off at this point, right, I mean I put all that effort into the initial pattern the other week after all! HOW LONG COULD THIS POSSIBLY TAKE! 🤦‍♀️

I cut it out with straight wide legs and like A LOT of seam allowance (like a solid 5cm or so) to make sure I could futz with it if needed, thread marked the seam lines (do not trust chalk on this fabric), sewed it up, only leaving the front bit open to pin closed later, and tried it on!

It didn't fit properly! (waistline not straight, crotch not the look I want) So I was going to have to do a bunch more fitting! Again! 🙃🤡

I thread marked the small new changes (straightening/lowering back waist line, crotch futzing in the front to get more space) and did the second fitting.

After that didn't make it work much better, I ended up ripping out most of the crotch middle seam in order to be able to adjust it more freely to figure out wth was wrong with it and how to fix it.

Added an ungodly amount in the middle section as you can see in the pics below (there's also a whole triangle in the back that you can't see properly in the back-view pic), took in some of the side bits to straighten out the shape again.

I pinned some of the top seam allowance to make a new, higher waistline as the previous one had gotten quite low and I wanted space to futz with.

I also pinned some of the back of the leg trying to fit it around the butt but I couldn't figure out where on earth I would transfer that fullness to to take it out of a seam, so I decided to leave it out for the next attempt for the time being. (Still market it on the pattern for now tho.)

Transferred the changes to the pattern (some of em didn't quite make sense (like that back middle crotch area doing a convex line instead of a concave one??) and had to be evened out to function)