#foxflash ECU programmer

[eobdtooluk-blog]

Foxflash Read and Write Renault EDC17C42 TC1767 on Bench

Foxflash ECU Programmer Customer Problem:

I can’t read id and flash?

Renault Trafic 1.6 Bosch EDC17C42

Tried via obd and also via bench mode, always same? Have this message: ERROR !!! contact support info@dfb-technology.com.

Eobdtool.co.uk engineer replied:

It cannot read via obd if there is no vr file in server.

double check wiring and voltage.

Foxflash will R/W in boot as well.

You may have problem with ecu.

Many customers read and write renault EDC17C42 by bench mode

R/W OK, Checksum OK.

Need to use Foxflash Bench Box, connect the power adapter to Foxflash or bench box are OK, there is no difference.

Reanult/Nissan TC1767 EDC17C42 Pinout to Foxflash ECU Chip Tuning Tool:

Pin Q4, D1: +12V (Red)

Pin J3: Brown

Pin H4: White

Pin H1: GND (Black)

Pin A1: CAN-H (Blue)

Pin A2: CAN-L (Orange)

To read and write use the following driver:

-> BENCH TRICORE

-> RENAULT or NISSAN

-> TC1767- RENAULT or NISSAN

-> EDC17 C42

If Foxflash ECU Tool read Renault EDC17C42 ECU on bench OK, but failed to write with the error “OTP sector not writable” as shown below.

The possible cause is that your file is bad.

Bad file tried to write the original file and see if all is ok.

Do checksum manually.

[eobdtooluk-blog]

Foxflash Read & Write Mercedes CRD3 via OBD Tutorial

Tutorial:

How to use Foxflash ECU Programmer and OTB 1.0 Expansion Adapter to read and write Mercedes-Benz CRD3 ECU via OBD driver?

What is foxFlash OTB 1.0 Expansion Adapter?

Foxflash OTB Adapter and Mercedes-Benz CRD3 ECU Pinout:

Need to connect the following 5 cables

CAN+: Pin 42

CAN-: Pin 55

+12V: Pin 5

GND: Pin 2

Ign: Pin 15

Check the corresponding Pin positions on Foxflash OTB Expansion Adapter

Then connect OTB Adapter and ECU correctly

Connect Foxflash and OTB 1.0 Adapter via OBD cable

Supply power to OTB Adapter as well

Read & Write ECU operation guide:

After connection, run Foxflash Manager and software

Select the driver and ECU you desire

For example:

Select CAR obd>> MERCEDES>> C KLASS>> 1.8/2.2 CDI Blue Delphi CRD3.x * CAN Fast

Enter the read and write interface

First, get ID

Then, read file and save the CRDF file

Next, open the CRDF-EGR DPF file

Last, write the file into the Mercedes-Benz CRD3ECU

All work fine!

[eobdtooluk-blog]

foxFlash OTB 1.0 Expansion Adapter

foxFlash OTB 1.0 Expansion Adapter is specially designed for foxFlash ECU Programmer extended application engine and transmission computers and ACM and DCM computer modules.

OTB expander package:

1PC OTB 1.0 expander

1SET OTB 1.0 conversion cable

1PC Paper Box

Adapter only, Foxflash hardware is not included.

For Foxflash ECU Chip Tuning Tool ONLY! Don't need to connect with bench box.

Don’t use it with PCMTuner ECU Programmer! Otherwise, the device will be damaged! (Illegal use can not be after-sales)

OTB= OBD mode via bench pinout (OBD on bench)

What can foxFlash OTB 1.0 Adapter do?

Dual-channel high-speed CAN

Three-way BOOT

Dual VCC power supply

GPT encryption and decryption function

Adaptive resistance

Adaptive CNF signal adjustment

Why does Foxflash team product this OTB 1.0 Expansion Adapter?

1.Ensure that foxFlash can be expanded to the OTB mode of BENCH PLUS in any OBD working mode

2.Achieve high-speed reading and writing

3.Ensure communication security and prevent the possibility of ECU brick due to voltage instability.

4.OTB reading and writing in OBD offline mode

5.ECM, TCM, ACM, DCM direct desktop mode reading and writing

6.Improve the reading and writing speed of some OBD drivers

Which car models can work with foxFlash OTB Adapter?

Visit https://www.dfb-technology.com/driver-list.html

Search for OTB to view the models and models that support OTB.

If the query mode cannot be displayed when opened, please clear the browser cache and reopen the website.

The foxflash OTB 1.0 Expander will be in stock after 2 weeks. If you are interested in it, please contact our customer service to pre-order it.

Email: sales@eOBDTool.co.uk

WhatsApp: +86 159 7293 3706

Skype: Eobdtool.co.uk

Business Time: Monday - Friday, 8:30am - 6:00pm CST (UTC/ GMT+08:00)

[eobdtooluk-blog]

Possible Foxflash Read/Write Citroen C4 Spacetourer MD1CS003 via OBD?

Is it possible to read/write Citroen C4 Spacetourer MD1CS003 ECU with Foxflash ECU Programmer via OBD?

Here is the clue:

1.Before 2020 Bosch MD1CS003 BENCH! Try bench it, if locked, then no tool can do in the worldwide till now.

2.On the bench it works for sure.

3.Bench. Tested and is OK.

4.2021 bench OK.

Foxflash Citroen C4 Spacetourer MD1CS003 Bench Pinout Diagram:

BOSCH MD1CS003 [TC298TP]- Peugeot, Citroen [Diesel]

Use:

Multifunction cable

Bench Box V.2

To read and write use the following driver:

->BENCH MODE

->CITROEN/ PEUGEOT

->TC298TP- PSA

->MD1CS003

[eobdtooluk-blog]

2023 Foxflash ECU Programmer Feedback: Read/ Write/Checksum OK

Here is the newest customer feedback about Foxflash ECU Chip Tuning Tool.

edc15 P+ BENCH Flash & eeprom Start

EDC15C3 (bench)– from Renault Laguna/ Read/Write OK

EDC15C13 (bench) — from Espace IV/ Read/ Write OK

EDC15C4 Full Flash R/W OK – obd-bench with 12v

edc15c13 renault BENCH Flash&eeprom Start

EDC16C1 E+F R/W OK – bench ok.

EDC16C9 bench R/W OK

EDC16C10 Read ok, Write ok, Checksum

Edc16c31 bmw bench r/w ok chck ok

EDC16CP31 BENCH DPF OFF R/W PERFECT

EDC16C3 R/W OBD CHECK OK

EDC16CP33 R/W OBD CHK INJCODE OK

Edc16c34 program disable while uploading, reads ok.

edc16u34. it worked reading and writing bench

EDC16CP35 READ/WRITE OK

EDC16C34 R/W OK Hardcut added & Car started perfectly psa

Edc16c39 can Read and write ok with obd Opel zafira B 1.9cdti 150cv

Edc16c39 fiat ducato obd R/W checksum ok

edc17c06 bmw BENCH, Read ok, Write ok, Checksum ok, car starts

edc17c08 bench ok

Edc17cp20 vag bench r/w ok chck okEcd17c70 obd ok

Edc17cp20, VR ok, write ok vw t6

Esc16c60 bench ok password unlock

EDC17CP01 V6 CDI Sprinter r/w ok bench

EDC7C3 bench r/w ok man bench

EDC17CP06 E+F R/W OK – bench

Edc17cp09 read/write ok chk ok

EDC17C10 Read ok, write OK, checksum ok bench

EDC17C11 bench R/W OK

EDC17Cp39 on Freelander 2 obd read write chk ok

EDC17C41_TC1797_ Bench bed written ok bmw

Edc17cv41 r/w cks ok.

edc17c42 bench R/W ok

Edc17cp44 bench read and write ok

EDC17CP45 BMW X6 D40 bench reading ok

edc17cp45 – “reading” (it is VR) via OBD. No file on DB but ID is working

Edc17c46 R/W bench OK!

edc17c50 TC 1797 BENCH r/w OK Mod Stage 1 with Display Calibration

EDC17CP54 on bench r/w all fine and easy. Cheksum with Winols.

Edc17c56 read ok Bench

edc17c59 BENCH Read ok, write OK, checksum ok opel

edc17c60 psa bench r/w ok

EDC17C64 bench R/W OK

Edc17c66 Mercedes r/w ok bench

Edc17c69 Iveco bench r/w ok chck ok

EDC17C79 Jeep Grand Cherokee full RW include checksum works OK

Edc17c84 r/w ok bench

EDC17C84 Opel vivaro 2018 with system adblue. with module 71

Delphi DCM3.5 R/W OK in JTAG

Dcm6.1 ford(psa) obd r/w ok chck ok

Dcm 6.2 obd ok

DCM6.2V Audi A3 2017 VR/Write ok

Dcm 7.1 boot ok

Crd2 Mercedes not work- read obd WRITE OBD FAIL- r/w ok by jtag

CRD3.10 Full bench read/write (flash+eprom) + auto checksum

Simos 8.10  obd  or boot car not start ecu problem

MEV17.4.2 READ MOD WRITE

ME 7.5 Full R/W , Stage1 all OK

Me7.6.2 opel bench r/w chck ok

ME7.6.3 Bench reading ok

MED9.1 bench R/W OK

medc17 bench R/W ok

MED17.2.5 R/W Ok Seam’s like a stable & Reliable tool, very Internet dependant.

Med 17.5.5 VW Scirocco 1.4 TSI 160CV Bench R/W – OK!

Med 17.7.7 Mercedes r/w ok bench

ME 17.9.6 read flash + eeprom ok

PCR2.1 Read MCU ID, ,Bench mode R/W, Online Patch unlock OBD, Checksum

MD1CP001 MB W213 2018y R/W OK , checksum calculated from the original file.

MD1CP014 bench r/w ok

MD1CS004 read + write OK audi

md1cs003 psa bench ok

Md1cs006 renault r/w ok bench

Mg1cs201 r/w bench ok

Mg1cs003 r/w bench ok

SID201 via OBD, success EGR OFF, read/write + checksum ok

sid206 obd read/write ok

Sid208 r/w ok

SID211 OBD OBDFORD TRANSIT ok

SID 305 tricore 1766 Micro Read/Write Boot Mode ok STG 1 DPF, EGR, DTC OFF.

SID310 READ PASSWORD, READ FLASH,READ EEPPROM, DTC OFF, FLASH WRITE, CHECKSUM

Sid803A PSA full system Clone done. Read in 15min, Write in 15min, Car Start

SID807 evo obd read ok, write mod ok. CHK MANUAL, program did not ask if it should correct or not

PCR2.1 obd vr/unlock/w ok

E83 full mode R/W dtc off, CS ok with ori file

E97 full system R/W ok

E98 bench r/w ok

MB175800 Denso Works Perfectly:)

FoxFlash Read & Write ECU Feedback: Success or Failure

[eobdtooluk-blog]

How to Fix Foxflash “Detected Potential Use of An Unofficial Adapter” Error?

Customer problem:

When I opened foxflash manager after downloading and activation, it appeared an error message “Detected potential use of an unofficial adapter. Device protection enable”.

eobdtool.co.uk engineer replied:

Foxflash server detects you using an unofficial adapter. So the device protection mode is enabled, and your device is locked.

Please don’t use the 3rd party adapters like ecuhelp OTB2.0 adapter to work with Foxflash ECU Programmer.

ONLY Use Foxflash OTB 1.0 Adapter!

Tech support:

Email: sales@eOBDTool.co.uk

WhatsApp: +86 159 7293 3706

Skype: Eobdtool.co.uk

Business Time: Monday – Friday, 8:30am – 6:00pm CST (UTC/ GMT+08:00)

[eobdtooluk-blog]

Foxflash Update Delco Bosch Siemens Phoenix MEDC17 ECUs

Foxflash ECU Chip Tuning Tool updated Delco Bosch Siemens Phoenix Tuning and new clone function on November 15, 2023.

After several weeks of extensive BETA testing for ECU and TCU, we are excited to announce the addition of a solution for this variant.

foxFlash is now able to perform the following operations:

New Clone Function

MEDC17

FCA

HYUNDAI

JAGUAR

LAND ROVER

SUZUKI

TOYOTA

On the following ECU reference:

BENCH

Delco E38 E67 E84 E92

BOSCH MG1CA007 MD1CS069 EDC17C11

BOSCH 6L45 6L50 6L80 6L90

BOOT

Siemens Continental SIM2K-305

BOSCH EDC17C11

OBD

Delphi DCM7.24

Delco E38 E92 E83 E80 E39A

Phoenix L40

BOSCH MD1CS069

Update method:

Try to update just connect, run manager and activate. No need to download, because the protocols are in the server.

If it fails, run foxFlash Manager, and click the Download button till all file download is complete.

[eobdtooluk-blog]

Read/Write CONTINENTAL SID310 ECU with 4 Tools

Here are some good ECU Programmers that support CONTINENTAL SID310 reading and writing:

Xhorse MultiProg, CG FC200, Alientech Kess3, Hexprog II.

1.Xhorse Multi-prog(Boot mode)

Price: €755 (EU/UK Ship No Tax free shipping)

Support Dacia, Renault, Opel, and Nissan SID310 EC

Multi-prog is available with English, Chinese. It has built-in update software, and supports free update online frequently.

Bonus function:

Built-in Script function

Support self-test and smart operation mode

Get free BMW ISN read function and NEC, MPC, Infineon, etc chip continuously update service

With free MQB48 license. Bind Multi-prog to VVDI2 full version or key tool plus to the same Xhorse app account to use MQB48 NEC35XX function.

Add VAG MQB RH850 dashboard processor(need separate RH850 cable for multiprog)

It can offer you the wiring diagram and which adapter is required to work with (click Detail after selecting the ECU type), and the user manual (click Help>> Help documents) in the Multi-Prog software.

2.CG FC-200 (Boot mode)

Price: €574 (EU Ship No Tax Free Shipping)

Support continental TC17 type engine computers SID310 (require software V1.1.6.0 or above)

FC200 is available in English and French, for Spanish, Polish, Turkish, and Traditional Chinese, you need to pay $150 for authorization. It supports free update online for one year (Annual fee will be €200/year after the first year)

It also has the wiring diagram in the software for reference.

Bonus function:

Read for BMW ISN Code by OBD

Support BOSCH MPC5xx platform mode ECU: MED9.1, MED9.5, MED9.5.10, ME9.0, EDC16CP31, EDC16CP35, EDC16C2, EDC16C8 (Need to buy extra FC200 MPC5XX Adapter)

Support GM E38, E39, E67 ECU, ZF 9HP Gearbox, etc.

3.Alientech Kess V3 (OBD and Boot modes)

Price: €779 (EU Ship No Tax Free Shipping)

Need to buy KESS3 software license separately

Focus on Dacia, Infiniti, Nissan, Opel, and Renault Continental SID310 ECU

Kess V3 supports multi-language and one year subscription for free upon activation. It has a Slave and Master version, and supports upgradable from Slave to Master. It can work with some existing KESS V2 cables for old models. Working with the unique Alientech Suite software, it’s super fast to read, write and calculate checksum for car, motorcycle, truck/tractor, agricultural and marine with separate protocols.

It needs to read ECU Password via OBD Protocol, and read/write ECU in boot mode.

Kess V3 Continental SID310 ECU Support List:

4.Hexprog II (Bench and Boot modes)

Price: $575.00 (basic set)

Hexprog II supports Bench Mode for Mercedes Benz and Infiniti vehicles, eliminating the need to physically open the ECU. Through ECU programming, users can clone and modify the ECUs, including Chip Tuning for enhanced performance.

To perform tasks such as ECU Repair, ECU Cloning, or read-write operations on the SID310 ECU, it is necessary to retrieve the OBD password from the respective vehicles of Nissan, Renault, Dacia, or Opel. In Hexprog II Tuner software, there is an option available to retrieve this OBD password, but it can only be done in boot mode due to the enhanced security of the ECU.

In addition, other China ECU clones like Foxflash, PCMtuner, Kess V2, and KT200 also can read/write CONTINENTAL SID310 well.

However, it’s recommended to use the original ECU programmer to ensure high quality and good after-sale service. Multi Prog and FC200 is more cost-effective to choose, and Kess V3 supports the most protocols but it's more expensive. Not one tool supports everything! You can have one or more tools depending on your need.

[eobdtooluk-blog]

OBDSTAR DC706 Reviews and Feedback

How about OBDSTAR DC706 ECU Tool? Compared with IO Terminal, any good?

DC706 has full clone function. It supports ECM, TCM and Body/other system clone via OBD or Bench. It can read ECU info, R/W Eeprom/Dflash/Pflash/MAP, reset ECU (Virgin), calibrate mileage, read IMMO pincode, and recover ECU... make ECU cloning easy.

It only costs a third of the Full version of I/O Terminal, therefore within everyone’s reach and without using a PC, with a Tablet and everything is done.

Besides, the updates are continuous.

The disadvantage is that it doesn’t do checksum.

Here we have collected many unbiased reviews from Facebook and our customers. Check the details below.

OBDSTAR DC706 VS I/O TerminalUnbiasedReviews:

Review 1:

I have the Obdstar DC706 and have used it a bit. I will say one let down was I was trying to harvest a virgin file from a 6L80 through OBD. It read the eeprom quickly but after 10mins and no movement on the flash, I gave up. I know many others have said IO terminal will through OBD and most have completed 6L80 on the bench. So far, that’s been my only issue. The monthly updates are great as they are adding many new modules all the time.

Review 2:

I have i/o terminal tool and dc706. dc706 is better overall. It is so easy to set up and go. The instructions are top notch, they use real pictures of the ecu and pin out diagrams are very clear, and then they even give you step by step instructions on how to do the job. They just came out with another huge update today, added many GM bcms and ford bcms. I have seen a post recently about someone cloning a ford bcm, said they couldn't do it by obd, but bench was fine. No tool is perfect, especially when it’s so new of a tool. They are quick to respond if you contact support. In many ways it's better than I/O terminal tool, you can virginize the gm bcm, mileage correction, pin codes all from the tool. It’s easily worth the $1400 price tag.

Review 3:

Io terminal vs 706 ....the cost is true, but Io will do more.

Review 4:

This Obdstar dc706 tool is a good companion to the IO Terminal. This tool includes cloning for many GM PCMs and TCMs. Ford DPS6 (Dual Clutch) TCM is covered. There is much more in there. I am testing a bit at a time but so far it is pretty good. I also got the TCM cable set and P003 bench adapter.

OBDSTAR DC706 VS Foxflash ECU Programmer Review:

I have both foxflash and dc706. dc706 is much easier to get going. The way they are updating the dc706 they will have more coverage in no time.

OBDSTAR DC706 Read/Write ECU/BCM/TCU Reviews:

Review 1:

2011 Citroen ds4 bsi continental Q0X SC667050+95256 perfect read of eeprom and flash and pin code and write.

Review 2:

My respects to this DC706 ECU tool. OBDSTAR simos 18.10 TC1791 by boot. With its adapter MP001.

Review 3:

I had a SIMTEC.75.5 and that read ok. Also, an E78 and E83. Both read ok. The E78 has the same processor as the E37.

Review 4:

i did a gpec2a with the 1000 ohm resistor and it worked.

Review 5:

Magneti Marelli fiat 8gmw worked flawlessly be careful to connect to the correct can hi.

Review 6:

I did it with 2017 Jeep renegade GPEC3 I done fine with it, 12v. Make sure you solder GPT1 well.

Review 7:

Read and write Saab Acdelco E67 very fast with the godiag breakout box.

Review 8:

Read and write VW IAW 9GV module ok

Read and write GM ACDelco E83 ECM ok

Read and write BCM module GM 52046112 ok

The tool has great potential.

Review 9:

Obdstar DC706 is the best for GM Delco E39 and E39A. Even Motorsport Flex didn't work on my last one.

Review 10:

I just went through the coverage and this dc706 tool just keeps on getting better and better. MEDG17 / MED17 found in Ford Models. The F150 Ecoboost is an MEDG17. This PCM has been a boot mode only PCM, now offered here in bench mode. I am also seeing the GPEC2 and GPEC3 PCMs listed in boot mode. Lots of FIAT BCMs are listed. This tool is the deal of the century.

Review 11:

I have had obdstar for month defects: no checksum, Renault ECU Sagem only wifi.

Review 12:

Very capable machine. They are quick to sort the issues. Doesn't do checksums. I do like it though. For money, I don't think it's bad at all. There's an extra or two you might want to buy as well. All in all, I'm glad I got one.

Review 13:

As time has gone on, the updates have sorted almost all issues. It has turned into a really good tool. Absolutely love it now though. Only thing really missing is checksum calculation. But saying that, it was never marketed as a programmer but a cloner so to speak. Don't know about VAG EDC17 immo calculation during writing with the OPT areas as it now has these in its list but I have other tools for that. It'll be interesting what’s coming in future updates. Would highly recommend it now.

Review 14:

Very capable machine. Had some issues 6 months ago. Nearly all sorted. Sometimes an update screws it up a bit (a week ago it was a nightmare - sorted now though) so best to wait a week or so and let others test. Still the odd ECU that still doesn't work after allegedly being fixed. It's definitely getting better. They are quick to sort the issues. Doesn't do checksums. I do like it though. For money, I don't think it's bad at all. There's an extra or two you might want to buy as well. All in all, I'm glad I got one.

Review 15:

It does read files ...and rewrite ...but not all ecus posted on the unit are fully functional...meaning u have to read .bin files use another system for example to clone or remove immo or remove dtc...and use dc706 to write modified file back...they are updating constantly adding new features or modules....it's not a silver bullet to do all units with every feature...no tool is that way...u need to find out exactly what cars and exactly what functions u need and buy specific tool..I have about 5 different tool still not able to do all cars or trucks ...one complain I have about dc706 is mostly covers Asia and Europe cars that are not sold in USA market so if u are Europe or Asia u will get more use out of it...but over all its a good one to have in ur arsenal ..as far as checksum goes it does automatically to my knowledge..if not true maybe someone can chime in.

Learn more:

[eobdtooluk-blog]

Kess V3 Clone VW DQ200 TCU Tutorial

Alientech Kess V3 is able to read and write VW DQ200 TCU via OBD and bench mode.

Let’s see how to operate on bench.

KESS3Special Price: €779 (€829)

Kess V3 OBD/Bench/Boot Protocols Promotion: Up to 50% Off!

EU Ship No Tax, Valid to March 15th

Protocol 1545 TEMIC DSG DQ200 VAG support ECUs:

0AM.927.769.D

0AM.927.769.F

0AM.927.769.M

Instruction:

Remove the ECU from the vehicle

Connect to the ECU

Select Identify ECU in the programming menu to allow correct recognition of the ECU

Always make a full backup of the ECU

Proceed with read backup and write backup.

Connection modes:

Plug in the bench power supply 1400K3ALIM to the KESS3 ECU programmer

Connect the cable 144300KBNC to the ECU connector, using the appropriate extensions 144300KTCU according to the pinout below.

Note: as an alternative, cable 144300T118 can be used.ColorDescriptionRedVECUBlackGNDWhiteCAN-HGreenCAN-L

Operation:

Connect Kess V3 to VW DQ200 TCU and computer by the corresponding cable, and supply power to Kess3 as well

Run Alientech Suite software

Update firmware to the latest version

Input dq200 to choose the desired TCU model (i.e. Audi A3 8P (2010) 1.2 TFSI S-Tronic 77 Kw)

Select Bench connection mode

Start to perform the read/write functions.

Identify ECU>> Read backup>> Write backup

It takes about 2 minutes to read backup the data, keep patient!

But it’s fast to write data!

Besides, Foxflash, PCMtuner, CG FC200, Launch X431 ECU & TCU Programmer, X431 X-Prog3 PC Adapter, Xhorse Multi-Prog, Yanhua ACDP 2/ACDP 1 with Module 13, Scanmatik2 Pro (SM2 Pro), Tactrix Openport 2.0, JLR Mongoose SDD Pro, Kess V2 also can read/write VW DQ200 TCU on bench.

Xhorse Multi-Prog Review: More Powerful Than VVDI Prog

Launch X431 ECU & TCU Programmer Audi Car List (Newest)

How to Clone VW DQ200 Gearbox via Launch X431 X-Prog3 PC Adapter?

Godiag GT107+ DSG Plus and Foxflash Read DQ200 DQ250 TCU

Godiag GT107+ Read DQ200 DQ250 with VCX SE/JLR Mongoose SDD Pro

VAG DQ200 and DQ250 Gearbox Read by Godiag GT107+ Scanmatik2 Pro (SM2 Pro)

Godiag GT107+ and Kess V2 Read DQ200/DQ250 Gearbox Data

VAG DQ200/DQ250 Gearbox Read with Godiag, PCMTuner, CG FC200 or Tactrix Openport 2.0?

How to Read and Write VW DL501 GEN2 TCM with OBDSTAR DC706 on Bench?

[eobdtooluk-blog]

Foxflash OTB Adapter Pinouts

foxFlash OTB 1.0 Expansion Adapter can be used with Foxflash ECU Programmer to read and write ECM, TCM, ACM, DCM via OTB mode (OBD mode via bench pinout ). Here eobdtool.co.uk shares the guide to find the Pinout for this OTB Adapter.

1.Open the foxflash Manager installation folder, and click the “DOCUMENTS.htm” folder

You can find the OTB pinout in this document folder.

Check the PDF format in “help” folder or check online version via browser.

2.Enter the ECU type you desire (i.e. CRD3) in the searching box to find the corresponding ECU quickly

Then the related bench pinout will appear on the interface (i.e. Mercedes- Benz Delphi CRD3.x)

3.There is no need to connect GPT. Only need to connect GND, VCC, CAN H and CAN L when you use Foxflash OTB 1.0 Adapter.

Check the CAN H, CAN L, VCC, GND position, and select Car OBD driver to connect with OTB.

You need to connect the Kline if have Kline.

Refer to the following post to check the connection method and the read write guide.

Foxflash and OTB Adapter Read & Write Mercedes CRD3 via OBD

[eobdtooluk-blog]

2024 Foxflash Tool FAQ

Here eobdtool.co.uk shares some newest common problems and solutions of Foxflash ECU Chip Tuning Tool.

Problem 1: Got “Invalid Class” Error

This error invalid class may appear when running foxflash software and cannot enter the file.

Solution:

It’s the operating system issue.

Better install software on a clean Win10 64-bit system.

If it is a Win10 64bit system, make sure the Windows Defender is off and the anti-virus program is off. Or try to reinstall the system.

Problem 2: Cannot find the SN of Foxflash ECU Programmer

Solution:

Check the device serial number on the backside of the foxflash main unit.

The Serial number is your code to activate the device.

Don’t release that SN to anyone. It’s a safe code for you. Don’t let any third party or guys know that code or it is easy to let your tools lock.

Problem 3: Cannot Find DFB2XX.dll

The solutions are different for the different situations below.

Situation 1: run foxflash Manager and appear this error.

Solution:

For 64bit system, Press “Install driver” to install driver.

For 32 bit system, the driver is not installed completely.

Go to FoxFlash/DFBTech_DRIVER/amd64 folder, copy and paste all files in this folder to C:/Windows/SysWOW64 folder

It’s better to install software on 64bit system.

Situation 2: Driver already installed. Foxflash Device is connected and the 12v supply is also connected.  Foxflash Manager works fine. But foxflash software cannot open and appear the error.

Solution:

Download the dll from the official site below.

Download here: https://aka.ms/vs/17/release/vc_redist.x86.exe

and for 64 bits https://aka.ms/vs/17/release/vc_redist.x64.exe for solve libcrypto-3.dll

Copy driver files from the driver map in your Foxflash installation folder to the Windows/system32 folder.

Tech support:

Email: sales@eOBDTool.co.uk

WhatsApp: +86 159 7293 3706

Skype: Eobdtool.co.uk

Business Time: Monday – Friday, 8:30am – 6:00pm CST (UTC/ GMT+08:00)

[eobdtooluk-blog]

Foxflash TRW EMS 2.x GM DQ200/250/DL501/VL381 TCUs Update

Foxflash ECU Programmer updated the newest software on Dec.6th, 2023. It newly added TCU GEARBOX TRW EMS Bench Beta Version protocols.

Update Info:

foxFlash Dev team is working on following operations:

Bench Beta Version protocols

TRW EMS

EMS 2.2 2.3 2.4 VOLVO TRUCK / RENAULT TRUCK

ACM / ACM2.1 MCM2 / 2.1

On the following TCU GEARBOX reference:

FORD POWERSHIFT 6DCT

GM-OPEL 6T3x

GM-OPEL 6T4x

GM-OPEL 6T5x

VAG DQ200 GEN1/GEN2

VAG DQ250

VAG DL501

VAG VL381

Thanks for the Foxflash develop team work on beta test version for new protocols.

Beta version is still in testing with the Dev team, keep follow us once stable we will publish soon.

[eobdtooluk-blog]

How to clone and do EGR & FLAPS off for Mercedes CLS 3.0 CDI 2008 diesel 220 ECU?

Hello, everyone! Today we have a Mercedes CLS 3.0 CDI 2008 diesel 220 ECU, and want to use Foxflash ECU Programmer to clone and do EGR & FLAPS off.

We do the pinout of the EDC16CP31 on its six wires it is connected

We have the pinout below.

I've already connected everything.

Turn on the power

Run foxflash software, select Mercedes>> MPC563\4-Mercedes>> EDC16CP31

Click OK

First click Connect

It will ask you to turn off the ignition

Internet connection Internet available

Turn on… So everything joined

We need to calculate Flash and micro.

Then click Read Ext Flash

This is how we write Mercedes CLS. It’s original.

Click Save to save the data

Next click Read Int Flash Micro

Click Save to save the micro (eeprom) data as well

After that, click Davinci-EGR_DPF_DTC.exe

Select the original ext flash data just saved

Detect successfully

Continue to turn off EGR and FLAPS

Deactivate successfully as well

Save the file

Click LSuite.exe

Select the EGR_FLAPS file just deactivated, and click Run

Recalculated successfully

Click Save to save this file

Finally, back to foxflash software to write ext flash

Select the EGR_FLAPS file just recalculated to write

Checksum computed in writing, no need to correct

Click No and wait the ECU writing is successful.

Done!

[eobdtooluk-blog]

Foxflash Promotion in October 2023: Buy Device Get 4 Free Gifts

Foxflash ECU Chip Tuning Tool promotion at eobdtool.co.uk in October 2023:

Buy foxflash with discount, and get 4 free gifts:

Latest price: €675

Buy Now: €655 (3% off)

Free gifts:

Toyota/Lexus BDM Jtag Solder Free Adapter

Two Pairs of FoxFlash Gloves

Fetrotech ECU Cover Extractors Set of 4

Headlight with Battery Three Gears Functions

Note: Gifts can be shipped later by another parcel. Please wait for the update. Every customer will have one.

foxFlash Higlights:

Master version

Full protocols open

VR read online work (some ECUs need to use our VR system, tool auto connect to our server download file)

ECU can be restored to original with foxflash tool if your ECU was damaged or meet some bad tuning

Free update! No subscription, no annual fee!

Support online and off line work (some ECUs and functions can work offline)

Auto checksum

Online support

Support multi-languages: English, Italian, Deutsch, French, Spanish, Polish, Portuguese, Czech, Romanian, Turkish

Two Years Warranty

Excellent technical support

Help desk and tuner account

ECU and TCU connect wires with pdf

Special functions

Auto support EEPROM and flash checksum

Support MEDC17 free clone service (most of others tool need patch the files after read out, but ours is free)

How to Use Fox Falsh to Clone MEDC17 via Boot/Bench Tricore

foxFlash Software can be download on official website: https://www.dfb-technology.com

FoxFlash ECU Car List

FoxFlash TCU Car List

ECU TCU List Online Check

Foxflash Manager APP can be installed up to 6 laptops

Supports WiFi hotspot, convenient for outdoor work

No VPN needed. Professional Online support, Faster server (1000M/S)

With the Latest firmware and updates. Use better quality BOM and PCB. More stable, full proof, and reliable.

There are many posts of Foxflash Ecu Programmer on our official blog website. Please follow it to learn more info.

[eobdtooluk-blog]

Foxflash User Feedback: Read/Write Toyota Denso NEC76F00XX BDM Success

Here shares the newest user feedback about  on Toyota Denso NEC76F00XX BDM full read and write with 14V better supply.

* Denso NEC76F0038AGD 175822-762 Toyota

* Denso NEC76F0038AGD 175822-773X Toyota

* Denso NEC76F0038AGD 175822-887 Toyota

* Denso NEC76F0038AGD 211941-37900830 Toyota

* Denso NEC76F0038AGD 211941-37910830 Toyota

* Denso NEC76F0038AGD 275036-1152 Toyota

* Denso NEC76F0038AGD 275036-2110 Toyota

* Denso NEC76F0038AGD 275036-2440 Toyota

* Denso NEC76F0038AGD 275036-2540 Toyota

* Denso NEC76F0038AGD 275036-3160 Toyota

* Denso NEC76F0038AGD 275036-4520 Toyota

* Denso NEC76F0038AGD 275036-4820 Toyota

* Denso NEC76F0038AGD 275036-9160 Toyota

* Denso NEC76F0038AGD 275136-1610 Toyota

* Denso NEC76F0038AGD 275136-2010 Toyota

* Denso NEC76F0038GD 175822-737 Toyota

* Denso NEC76F0038GD 175822-762 Toyota

* Denso NEC76F0038GD 175822-773 Toyota

* Denso NEC76F0038GD 275036-0080 Toyota

* Denso NEC76F0038GD 275036-0360 Toyota

* Denso NEC76F0038GD 275036-1152 Toyota

* Denso NEC76F0038GD 275036-1470 Toyota

* Denso NEC76F0038GD 275036-2880 Toyota

* Denso NEC76F0038GD 275036-7461 Toyota

* Denso NEC76F0038GD 275036-8730 Toyota

* Denso NEC76F0038GD 275036-9540 Toyota

* Denso NEC76F0038GD 275236-0011 Toyota

* Denso NEC76F0039AGD 175822-762 Toyota

* Denso NEC76F0039AGD 175822-773 Toyota

* Denso NEC76F0039AGD 175822-799 Hino

* Denso NEC76F0039AGD 175822-887 Toyota

* Denso NEC76F0039AGD 211941-37000930 Toyota

* Denso NEC76F0039AGD 211941-46000930 Toyota

* Denso NEC76F0039AGD 275036-1152 Fujitsu Toyota

* Denso NEC76F0039AGD 275036-3740 Toyota

* Denso NEC76F0039AGD 275036-9050 Toyota

* Denso NEC76F0039AGD 275036-9170 Toyota

* Denso NEC76F0039AGD 275136-1910 Toyota

* Denso NEC76F0039GD 175822-737 Toyota

* Denso NEC76F0039GD 175822-762 Toyota

* Denso NEC76F0039GD 175822-773 Toyota

* Denso NEC76F0039GD 175822-887 Toyota

* Denso NEC76F0039GD 275036-1150 Toyota

* Denso NEC76F0039GD 275036-1152 Toyota

* Denso NEC76F0039GD 275036-6941 Toyota

* Denso NEC76F0039GD 275036-7780 Toyota

* Denso NEC76F0039GD 275036-9160 Toyota

* Denso NEC76F0040AGD 175822-652 Hino

* Denso NEC76F0040AGD 175822-887 Toyota

* Denso NEC76F0040AGD 211841-3581A830 Toyota

* Denso NEC76F0040AGD 275036-9170 Toyota

* Denso NEC76F0040AGD 275922-856 Toyota

* Denso NEC76F0040GD 175822-666 Toyota

* Denso NEC76F0040GD 175822-887 Toyota

* Denso NEC76F0040GD 275036 6941 Toyota

* Denso NEC76F0040GD 275036-2050 Toyota

* Denso NEC76F0040GD 275036-7341 Toyota

* Denso NEC76F0040GD 275036-7780 Toyota

* Denso NEC76F0040GD 275036-9170 Toyota

* Denso NEC76F0070 275036-3410 Toyota

* Denso NEC76F0070 275036-3560 Toyota

* Denso NEC76F0070 275036-5130 Toyota

* Denso NEC76F0070 275036-5920 Toyota

* Denso NEC76F0070 275922-001 Toyota

* Denso NEC76F0070 275992-428 Toyota

* Denso NEC76F0070 276122-092 Toyota

* Denso NEC76F0085 211941-45800932 Toyota

* Denso NEC76F0085 275036-5280 Toyota

* Denso NEC76F0085 275036-5650 Toyota

* Denso NEC76F0085 275036-5810 Toyota

* Denso NEC76F0085 275036-6110 Toyota

* Denso NEC76F0085 275036-7400 Toyota

* Denso NEC76F0085 275036-7581 Toyota

* Denso NEC76F0085 275922-022 Toyota

* Denso NEC76F0085 275922-320 Toyota

* Denso NEC76F0085 275922-473 Toyota

* Denso NEC76F0085 275922-500 Toyota

* Denso NEC76F0085 275922-532 Toyota

* Denso NEC76F0085 275922-828 Toyota

FoxFlash Read & Write ECU Feedback: Success or Failure

2023 Foxflash ECU Programmer Review: Read/ Write/Checksum OK