#watercool

[bigfatbreak]

Birds of a Feather previous / next

[glowcircuit]

I built a miniature Va11 Hall-A Bar inside of my PC!!

Va11 Hall-A PC Parts & Build list

PC:

CPU : Intel I9 14900k

GPU: Intel Arc A770 16gb

Ram: Corsair Dominator 64gb 5600

Mobo: Maxsun Terminator Z790 D5 wifi

Hard drives M.2: Samsung 990 pro 2tb, Samsung 970 evo plus 1tb, CT 1tb,                                 Adata 500gb

PSU: ROG Thor 850 P2

Cables: Cablemod.com custom shortened and sleeved

Water loop distro : EKWB FLT 120 reservoir + D5 pump

Water loop cpu block: ThermalTake Pacific Mx2 Ultra 

Water loop radiators: Alphacool HPE 20 x 2

Water loop hardware: 15 Alphacool, 3 EKWB, 2 Alphacool soft, 2 granzon    

Water loop tubes: EKWB Acrylic tube 14mm, Alphacool 13/10 soft

Air Cooling : ThermalTake Toughfan 120mm x 3  + Controller

Air Cooling : Noctua 40mm pwm server fan x 2 (non visible)

Additional RGB Control : Coolermaster controller

Case:

Lian Li PC V600, left side mount, released in 2006, I acquired it in 2015 from PC Recycle in sodo Seattle.

I had to track down a new foot, one had been missing since I acquired the case (ebay)

Mods:These are the case mods I did personally

Cut a hole for the cpu mounts in the Motherboard mount plate as this case was designed for older hardware 

Cut two 120mm blowholes and added aluminum covers (Dremel)

Cut Front and rear windows into side panels (Dremel Max)

Moved PSU from vertical placement in the lower right side of the case in front of the CPU  to horizontal placement in the top left in old drive bays. 

The PSU bracket had to be cut to show the OLED on the side. 

Modded the side panel rail slide to accommodate the PSU, I used the original aluminum stand the psu was on, cut in half and epoxied with JB weld. 

Changed and moved Power/ Reset switch to the back of the case, shortened and spliced the cable

I cut and bent my own 14mm acrylic tubes (hobby miter, heat gun). 

Cut and made two way mirror for the front panel

Plastic "truss" is both functional and aesthetic. It came from a Gunpla accessory kit and has two cables passing through it and it acts as the GPU support. I could only get red and had to paint it.

Notice that some logos are missing/ covered, I dislike having a case as an advertisement. The Rog eye on the PSU is mostly covered but iykyk, most of the word "Intel" on the ARC GPU, Two of the Thermaltake logos on the fan edges, the Paint on the Thermaltake Mx2 Ultra and Maxsun terminator heatsink. (I will eventually cover the visible SSD with a heat sink, cover the fan info on the rear and work a cover for the word "dominator"). the one logo explicitly unchanged is the LianLi case badge, if I think of a perfect replacement, maybe then.

Mod I did not do:

I did NOT shorten and sleeve my own cables, I used cable-mod.com. I am not confident in my ability to do this.

BAR:

"Bar Tiny" Re-ment sets from Japan, 17 sets involved. 

 I customized the color of the bar and chairs and shortened one table for the mezzanine. The whole bar, minus barback- is on a removable 7 inch piece of black acrylic for cleaning.

Jill Stingray Nendoroid

Jils Cat, it sleeps on the GPU

Jill Stool: Jill is glued to a cute doll stool to see over the bar

Jill Accessories non-Nendoroid: cellphone, purse, coat (ebay)

Dorothy Haze Nendoroid

will be added on release.

Bar Back:I made this myself

Black acrylic sheet, and frosted acrylic rods.

Doll Light power kit: 8 Led lights, 4 incandescent lights

USB Doll light power strip

Other Bar Accessories:

Overhead Hanging farmhouse light

trash, mop, broom, pan, mop bucket, 

2 blue fuzzy chairs 

Miniature plants

Miniature Microphone

Mini bottle Dom Perignon, an xmas gift from my friend nemo, it's

 on the top shelf 

Problems and changes:

1. ARGB, pretty pretty pain in the ass. 4 pieces of software........

2. The water loop was changed extensively as hardware came in and space limitations were discovered. The biggest change is that I originally planned to have one radiator on the front of the case, the tubes running over Jills head and to light the tubes as lighting for the bar, to do this the fan would have been in the case proper pushing the whole bar to far into the mobo, it didn't work, so the loop was moved to the top of the case and caused me to have one complex bent tube 

 Second, I had planned the loop to use one sideport on the distro, but space limitation moved both ports to the top causing the complex fittings setup in that corner.   

3. The MOBO, sigh. This has been clearly the most challenging choice I made in this build, I really wanted it to work perfectly too, but I rolled those dice because: Aesthetic+function, the board I wanted (https://en.colorful.cn/en/home/product?mid=84&id=400d19bc-5655-49e1-b391-df00b60935ef) was to great a risk for the cost. This was a silver medal. 

I generally dislike the design options I had in the Z790 series of the big board makers (I  HATE big logos), especially the full ATX, there was one M that interested me, I should have picked it . This board has potential, but the BIOS is underdeveloped and compatibility has been problematic, I had to do a tricky outdated style BIOS update right from the box, and have had to reset the cmos a couple times. It skips BIOS on general boot and though stable, it will have to be addressed eventually, it doesn't have a proper sleep because of some issue between uefi & legacy. It may end up replaced, which will require a full build teardown.

the Turbo fan built into the board doesn't seem to function

Alos, the two argb connections on the mobo dont work, or I can't get them to recognize anything, necessitating the Coolermaster controller for the PSU and Distro. it is shoved behind the distro along with a Noctua 40mm

[ianthedebonair]

never a great time to be alone with your thoughts

[mr-orion]

sometimes you gotta hype yourself up and color your sketches... anyway, Ray's about to ask you something very on the nose and it's gonna hurt. You should watch out.

[pikslasrce]

me (internally): oh my god. another gay perso– wait its not right to assume peoples identity based on stereotypes like tha– but look at him. the mullet. the chunky highlights. the way he talks– okok. im not the only gay person h– WAIT hes coming this way look approachable

me (externally): *stares homophobically*

[saintxgerard]

He is my cubicles woman. That’s what he is to me rn

[numbuh424]

maybe I've just watched too much taskmaster but tbh someone fucking the donut would not have been shocking at all. it would've been par for the course at this point, really.

[ja3yun]

i am a yapper until i die. i will yap your ear off all day and all night with no room to breathe

[badnewswhatsleft]

my coworker kinda.......😳

[cheekedupwhiteboy]

reading more about eternal president matthew mullenweg @photomatt's recent fuckups on automatic's other products... complete with getting his fee-fees hurt and passive aggressively threatening to give up on wordpress entirely just like he did with tumblr today lol

[kettle-cover]

William, they almost kissed 🤦

[thelastlaff]

does anyone else look at the half of chip revvington’s place (cut to the chase) covered in red solo cups and a trash bin filled to the brim with trash and think about the implications

and the fact that the lamps are all crooked probably from him throwing them so often

[scullys-scalpel]

What everyone looks like at the DMV, down to the water cooler and guards

[marciliedonato]

*leaning over* hi gongeous....*trips and hits my face on the watercooler* *spills my documents revealing 100 pics of CEO mx way* UM. THATS NOT MINE

[somelikeitbrugh]

I think about this scene once a week. 🤣

[foobars-cool-car]

try my mitski song its called A Boy called Water Cooler