#artkalbeads

[jayflemart]

[cristalika]

[lemonykeeby]

making jyushi from artkal beads bc hes too cute not to

[pixelmischief]

👁️👁️👁️👁️👁️ BE NOT AFRAID!!!! 👁️👁️👁️👁️👁️

[kamapixel]

My once in a blue moon update once again, I saw folks were liking the One Piece stuff I posted awhile back and I did more since then, the highlight being the original art I had commissioned for a Going Merry to match the Thousand Sunny.  Seems like a good time to post this too with the recent One Piece Netflix trailer out.

[sesa-senpai]

I love omori and artkal beads

Now I need to make them more, because 3 pairs were not enough

[threeboy]

The Perler Bead Flat Melt "No Poke" Tape Method

I like the "flat melt" look of Perler beads it makes them look more like videogame sprites. The problem with the flat melt is it really heats up the peg board which warps and wrecks it for future creations. You can avoid heating your peg boards by using "The Tape Method" but you can end end up with trapped air "blow outs" that wreck the final piece unless you poke holes. Poking holes is tedious and disaster prone so I've been experiencing with this pokeless method...

Let's use our good friend Bowser here to demonstrate:

Make your bead art normally

Make your bead art as you normally do. Since we will be using tape to remove the beads off the board the final work will be flipped horizontally or "mirrored" so keep that in mind.

Use masking tape to cover the beads

Masking tape or painters tape work well. If the tape is curly and you’re hesitant you can wreck the beads so go gentle but boldly. Press tape down on entire piece with finger, popsicle stick, anything you want just make sure all beads are stuck to the tape.

Gently take the beads off the board and set it on your ironing surface tape down beads up.

Iron only until beads begin to fuse

Add your parchment paper and start ironing. Try to use new parchment paper (buy a roll from a grocery store) since the paper Perler provides has creases and they can transfer to the final piece - fresh is best and will ensure smoothness.

For ironing I use a medium-high heat on the iron and keep it moving constantly. I rotate the artwork every 20 seconds so it's heated evenly.

Lift the iron every so often to see the progress of the melted beads (through the paper). You want a partial melt where the beads are fused and start to get square shaped but don't go for the full flat melt yet.

Remove the tape carefully!

Flip the art over, carefully remove the tape, then flip it back and resume ironing and go for the full flat melt. The beads should stick to the parchment paper a bit.

Iron more and occasionally look at the beads through the paper (don't remove the paper it can create streaks) to see the progress of the melt.

After ironing I put a heavy book on top of it so it stays flat as it cools. The total cooling should only take 5-10 minutes.

All done!

After the final piece has cooled and you remove the paper If you find there are still small holes you can put heat/parchment paper back on and iron more just don't remove the parchment paper mid-iron with warm beads because it can create streaks.

If you iron too long you may run into the issue of colors bleeding into each other so find the balance you are comfortable with.

Hope this saves some pegboards and frustration.

[millroadcrafts]

Happy Halloween!! #millroadcrafts #artkal #artkalbeads #mrcbeads #3dfusebeads #perler (bij Millroadcrafts.nl) https://www.instagram.com/p/CkWdBEIo5Jt/?igshid=NGJjMDIxMWI=

[polykrom]

"L'homme qui chavire"

September 2022

[theoceanisnotsilent]

Our favourite little forest guardian #Totoro. He is made out of perler beads and has a little stand, perfect for displaying on flat surfaces! I only have a few in stock, and I don't use perler beads as a medium for crafting anymore, so once these are sold, there won't be any more. Get yours while you can in my Etsy shop!⁠

[jayflemart]

Lamplighter

[tinythings-es]

Star Guardian Akali 😍💜✨️ ▫ ▫ ▫ ▫ ▫ #perlerbeads #hamabeads #artkalbeads #fusebeads #pixelart #perlersprite #videogames #hama #pixelart #handmade #gaming #mypixelartworld #akali #starguardian #leagueoflegends #akalistarguardian  #videogamecollection #instagamer #retrogamer #retrogaming #moba  #gamingcommunity #retrogames #instagame #retrogamers #retrocollective #retrocollector #gamesroom #retrogaming #riot https://www.instagram.com/p/Cf7fItzD9HD/?igshid=NGJjMDIxMWI=

[the-catnip]

Eeveelutions with artkal minis. Check out the TikTok for the process video!

[kamapixel]

I had made a few more TMNT: Shredder’s Revenge stuff since the last ones, including the recently announced Usagi.

[jessicarabbitworld]

This is awesome! What say you - should it be in a white frame or a black frame? ⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️ Repost from @caveofpixels • Who framed Jessica Rabbit? ME! Although I'm thinking maybe a white frame might be better, what do you think? #whoframedrogerrabbit #jessicarabbit #perlerbeads #artkalbeads #hamabeads #fusebeads https://www.instagram.com/p/CclaEfvuCwd/?igshid=NGJjMDIxMWI=

[millroadcrafts]

Beautiful Pikachu cosplaying as Meouth!! #millroadcrafts #mrcbeads #artkal #artkalbeads #artkalbeadsart #beadsart #hama #hamabeads #perler #perlerbeads #pixel #pixelart #3Dbeads #fusebeads #fusebeadsart #Spriteart #fusebeads #ironbeads #Mrcbeadsmidi #mrcbeadsmini (bij Millroadcrafts.nl) https://www.instagram.com/p/Co0WRtoIv1T/?igshid=NGJjMDIxMWI=