#programmable thermostats columbus ohio

[ohioelectricityrates]

3 Big Ways to Cut Your AEP Columbus Electricity Bill

New Post has been published on http://www.ohenergyratings.com/blog/2018/07/27/3-big-ways-cut-aep-columbus-electricity-bill/

3 Big Ways to Cut Your AEP Columbus Electricity Bill

Air sealing and insulation are two of the most effective ways to cut your energy usage and reduce you month electric bill year ‘round.

How can I lower my Columbus electric bill?

It can be difficult to tell how much energy you’re using until you get your AEP Ohio electric bill at the end of the month. Even then, without a breakdown of where you’re spending energy, you may not be sure of what’s going on in your house to cause your electric bill to be too high. Luckily three of the biggest ways to cut your energy bill in Columbus are the same for any household and are pretty simple to do!

Save on electricity with a thermostat setback

A 7-10 degree setback for 8 hours a day could cut 10% off your electric bill. Start by setting the thermostat temperature at the highest comfortable setting while you’re home; 78 degrees or above. When you’re out or away, set the temperature higher by 7-10 degrees. When you’re sleeping, you may be able to avoid using the AC altogether if the outside temperature will be below 78 degrees most of the night. A programmable thermostat makes the job effortless. But if you don’t have a programmable thermostat, remind yourself to change temperature settings with an alert on your phone or a note taped to your door.

Make you home more energy efficient by air sealing and insulating

It costs a lot money to condition your air all summer. It costs even more when warm, humid air from outside is constantly leaking inside through poorly sealed doorways or insufficiently insulated walls and ceilings.

Keep more cool air inside your house by air sealing your home. For many new homes, that just means adding or replacing weather stripping around doors and windows. Caulk around window frames to ensure a good seal and on old wooden sash windows, look for damaged or missing glazing and seal the glass with silicon caulk.

Adding insulation to your attic is another key component in efficiency that can complicated and expensive, especially in an older home. Replacing or adding insulation to a finished space can be an expensive fix. However, in both cases, the change in comfort is immediate and will pay for itself in savings within a few years.

Another easy tip is to hang insulated window treatments throughout the house. In summer, they reduce heat gain by 15% and winter time heat loss by 40%.

Save money on electricity with a cheap fixed rate plan from an AEP supplier.

Finally, one of the best ways to lower your electric bill is to find the best provider in Columbus with a low rate. At Ohio Energy Ratings you can view all available electric plans in your area and compare apples-to-apples to find what works best for you. Get the scoop on rates, fees, terms and conditions, and more all in one place. Then simply choose a new electric supplier and switch to a plan that will save you money.

Start comparing Ohio electricity rates today and you could be saving money by tomorrow! Visit us here: https://www.ohenergyratings.com/electricity-rates.

[moore15263212-blog]

Air Conditioning Repair Fort Worth Texas

Air Conditioning Repair Fort Worth Texas - Call +1 844-293-3806 http://www.hvacrepairservice.info/

Strategies The HVAC in Fort Worth Texas Experts Don't Want You To Know in Air Conditioning Repair Fort Worth Texas

People that have HVAC in Fort Worth Texas solutions understand how important it can be to have the one that works appropriately. It could be very costly to get a unit that is not going to work properly. These sentences are loaded with helpful suggestions you can use to keep the residence heating system, venting and Air Conditioning repair in Fort Worth Texas working in prime situation, so read through them all!

Before you begin getting in touch with to locate somebody to fix your unit, make sure you know the type of process which is installed. Find out the brand and product and, if you can, look the routine maintenance record. That way you can provide the professional with all the important information.

Your outdoors condenser enthusiast might be assisted to run greater on your part washing the enthusiast rotor blades and coils just before summer time establishing. Be secure and switch off the energy provide prior to caring for your HVAC in Fort Worth Texas unit. Eliminate simply leaves and trash through the condenser outdoors.

Clean the enthusiast rotor blades and coils just before summertime. Always turn the unit off before you do anything whatsoever with it, which includes inclined. Additionally, it's important to get rid of simply leaves as well as other trash externally condenser unit.

As soon as the simply leaves learn to fall, the HVAC in Fort Worth Texas devices might be harmed. Be sure the fan's barbecue grill is cleaned usually in the fall. The enthusiast demands unblocked air-flow, of course, if trash is stopping this air-flow, your process could endure.

You should lubricate parts of your enthusiast condenser. These are generally covered with rubber or metal hats. Try to find an oils which is light after which place about 10 drops inside of the harbour. You don't desire to put in an excessive amount of.

Getting a programmable thermostats can be quite a terrific approach to recognize cost savings. In the event you adapt it to keep your house a bit hotter or a little cooler in the time you happen to be getting to sleep, you could see your vitality monthly bill drop up to ten percent. Also, you'll discover that you can system your thermostat coming from a computer or anything connected to the website.

Have your Air Conditioning repair in Fort Worth Texas process inspected every six months. The optimum time of the season to get the process examined is right before the weather actually starts to alter. This kind if precautionary routine maintenance is tremendously required to defend against any expensive problems from approaching your way.

If there isn't anyone in your house, then there's no need for the Air Conditioning repair in Fort Worth Texas unit to become working and losing electrical power. By elevating the temp from, by way of example 78 to 80, your home will probably be hotter, only as much as 80 prior to your Air Conditioning repair in Fort Worth Texas kicks in. If you decide to establish the temp to 82 or 83 roughly on, your Air Conditioning repair in Fort Worth Texas won't carry on till it actually reaches that temp. The more the unit keeps on, the more it ultimately ends up charging you in vitality monthly bills.

If no one is residence, switch off the environment conditioner to save money. Whenever you change it off, your house warms up, only into a certain tolerance. Certainly, if you depart your Air Conditioning repair in Fort Worth Texas establish at the low temp the whole day even though you're not residence, you'll pay to keep that low temp.

Occasionally, you might be perplexed when searching for an HVAC in Fort Worth Texas process. Fortunately, these guidelines will assist. Reference these guidelines when you pick your HVAC in Fort Worth Texas process.

Additional info on the subject of Air Conditioning Repair Fort Worth Texas https://en.wikipedia.org/wiki/HVAC https://cathey45043171.tumblr.com/post/173562018002/air-conditioning-repair-columbus-ohio

[danielromanousa]

How Much Does Floor Heating Cost in Dayton, OH?

Dayton is the sixth-largest city in the state of Ohio and the county seat of Montgomery County. The region is just north of Cincinnati and has a population of around 1 million people making it Ohio’s fourth-largest metropolitan area, after Cleveland, Cincinnati, and Columbus. Thanks to the Wright brothers, Dayton is the historic birthplace of powered flight.

Dayton’s climate is classified as a humid continental climate. On average, there are 4.5 nights of sub-zero degrees Fahrenheit lows annually. Based on currentresults.com temperatures are coldest in January with highs around 36 degrees Fahrenheit and lows around 22 degrees. Snow is moderate, with a normal seasonal accumulation of 23.3 inches (59 centimeters) usually occurring from November to March.

It’s Easy to Add Affordable In-floor Heating to the Bathroom, Kitchen, or Any Room in Your Home

Recent data on listing terms when selling a home uncovered some popular home features, among those heated/radiant floors. It makes sense that if people are looking to buy a home with these amenities, then existing homeowners should consider them when remodeling. WarmlyYours has an underfloor heating system for most any application and any room in your home. Here are some room examples along with compatible flooring selections.

No More Cold Bathroom Tile with Underfloor Heating

These Dayton homeowners needed to warm up the elegant but cold tile flooring in their newly remodeled bathroom, so they decided to add radiant floor heating to their medium master bath. Radiant heating is the perfect solution to bring welcoming warmth and luxury to your daily routine.

Low Cost per Square Foot of Radiant Warmth and Low Operating Cost Make This Bathroom Affordably Cozy

For their project, these owners selected a 1.5- by 38-foot TempZone™ Flex Roll to install in their 70-square-foot bathroom. The cost was only $598.50 or $10.50 per square foot. In addition to the material cost, the operating cost should also be factored into the remodeling budget. WarmlyYours’ Operating Cost Calculator figures in the average kWh cost in Dayton of 11.79 cents resulting in a daily cost of 43 cents to heat this bathroom for four hours a day, a small price to pay for the comfort and luxury of a soothingly warm bathroom tile floor. Furthermore, the system can be the primary heating source for the room which is an additional cost and energy savings advantage.

Calculating Costs for Heating Up a Laminate Kitchen Floor

As their kitchen was one of the most used rooms in their home, these Dayton homeowners knew it made sense to add electric in-floor heating when planning their kitchen remodeling project.  To warm up the stylish but cold laminate flooring they had selected they chose to install an Environ Flex Roll floor heating system in the 123 square foot space for $860.00 at a cost of approximately $12.00 per square foot. The Flex Roll consists of an insulated heating cable sandwiched between two layers of reinforced, durable aluminum foil that radiates 12 watts per square foot.

Around 75 Cents a Day Will Heat This Kitchen Flooring

Factoring in the cost for operating the system is important when planning your budget. WarmlyYours has a useful online tool to help you do just that. Based on WarmlyYours’s Operating Cost Calculator it costs just 76 cents to heat this kitchen for eight hours a day. An added bonus is that this system can be a primary heat source for the room without incurring additional heating bills.  

TempZone™ Cable Warms up this Office for Less than a Dollar a Day

This homeowner decided to install radiant heating during a recent remodeling of their home office to minimize the winter chill. The system was designed to heat the floors of their office with 300 feet (75 square feet) of 120-volt TempZone™ Cable for $480.00. That amounts to just $6.40 per square foot. By adding a nHance programmable thermostat for $169, it brought the total to $649.00. 

Operating Cost is Low to Heat Underneath Wood Flooring

It’s important to consider the operating cost of your floor heating system when budgeting for your own project. WarmlyYours makes it easy for you with our Operating Cost Calculator. Based on the data from this tool, the cost to operate this system for 8 hours a day is just 46 cents. This calculator factors in the average kWh cost in Dayton, which is just slightly less than 12 cents. Best of all, this radiant heating system can be the primary heat source for the room so there’s no need for additional heating and higher energy bills.

Add a Basement Bedroom Complete with Radiant Floor Heating

These Dayton homeowners decided to add a basement bedroom for visiting friends and family, but were concerned about the cold basement floor. They discovered that electric radiant floor heating would be an ideal solution to that dilemma. They immediately ordered a WarmlyYours underfloor heating system for installation under new laminate flooring to keep the guest bedroom comfortably cozy during the winter rainy season.

Product Cost per Square Foot, Plus Operating Cost for the System

The 1.5- by 52-foot TempZone™ flex roll fills 78 square feet of floor space and costs $741, which equates to just $9.50 per square foot. The flex roll is easy to cut and turn to effectively fill the floor space with 15 watts per square foot of soothing radiant heat. They were also pleasantly surprised to find that operating the in-floor heating is also affordable. According to WarmlyYours’ Operating Cost Calculator, it only costs 48 cents a day to heat this bedroom for eight hours.  The floor heating system can be the primary heat source for this room, so there won’t be any additional heating bills which is a welcome bonus.

Our Easy to Use Operating Cost Calculator Gives Cost To Run An In-floor Heating System

After you’ve chosen your floor heating system including how you’ll use it, you can calculate how much it will cost to operate. Actually, the calculating is done for you with the Operating Cost Calculator, a useful online tool that asks basic project questions; product type, room size, local energy rate and daily usage in order to calculate the daily, monthly and annual operating cost of your system. It’s simple to use.

To get started just use the calculator below:

Floor Heating Controls and Costs to Suit Your Lifestyle and Budget

Customize your comfort with the nSpiration series of thermostats from WarmlyYours. Each control has been tailored to meet a specific need.

From programmable models that allow you to easily monitor and manage your home comfort remotely from any device to controls where you can set it and forget it, all of our controls are designed to help you get the most out of your floor heating system. For large applications, or additional areas, you may have to combine the nJoin power module with your nSpiration Series thermostat.

nSpire Touch Wifi Programmable

Control your floor heating system with your smartphone or on the web with the nSpire Touch WiFi thermostat. The added ability to be controlled remotely can accommodate busy schedules. It also offers substantial energy savings without sacrificing comfort or convenience.  

nSpire Touch Programmable

It’s easy to set up a radiant heating system according to your preferences and schedule with the integrated Install Wizard included with the nSpire Touch. With 4 programmable events for each day of the week, the nSpire Touch allows you maximum control over the floor temperature.

nHance Programmable

You can easily set this control up for your exact needs and specifications with the nHance intuitive user-interface. For consistent schedules, it will deliver a maximum level of comfort when you need it most, like during your morning routine, while still keeping your overall energy use to a minimum.

nTrust Non-Programmable

Ease and reliability are benefits of the nTrust  thermostat. Because there is no programming required for the nTrust dual voltage (120V/240V) control, you can just set it for your desired temperature and then sit back and relax. 

Radiant Floor Heating Technical Installation Support Available 24/7

Our 24/7 technical support experts will be on hand to guide you every step of the way through your installation, whenever you need assistance. Ensuring your project goes smoothly is WarmlyYours commitment to you, so whenever you are ready to install your system, we will be there for you day or night.

Get Started Quickly with our Radiant Heat Cost Calculator and SmartPlan™

Using our Radiant Heat Cost Calculator is the easiest way to plan for adding electric floor heating to your next project. All you need to do is fill in some basic information about your project and the cost calculator tool will give you a side-by-side comparison of the recommended products and costs for your room. Using this tool allows you to plan and budget for your own project online. Get started right now by clicking here.   

The next step is to upload a floor plan of your room to get your radiant heating SmartPlan™. This plan provides more in-depth detail than a radiant heat cost calculator because it shows exactly how the floor-heating system should be laid out with the electrical plan. This custom SmartPlan™ helps ensure an easier install by helping our expert technical staff guide you through the complete installation process.

If you have any questions, there are several ways you can reach us. 1) Call us at 800-875-5285, 2) live chat us at www.warmlyyours.com, or 3) email us sales@warmlyyours.com. Whether you live in Dayton or another city that could benefit from our radiant heating solutions, WarmlyYours is ready and waiting.

Skyline image: By MarkDonna at the English language Wikipedia, CC BY-SA 3.0, https://commons.wikimedia.org/…

from WarmlyYours Blog https://www.warmlyyours.com/en-US/posts/how-much-does-floor-heating-cost-in-dayton-oh source https://warmlyyours.tumblr.com/post/173483424321

[jessicaboyerus]

How Much Does Floor Heating Cost in Dayton, OH?

Dayton is the sixth-largest city in the state of Ohio and the county seat of Montgomery County. The region is just north of Cincinnati and has a population of around 1 million people making it Ohio’s fourth-largest metropolitan area, after Cleveland, Cincinnati, and Columbus. Thanks to the Wright brothers, Dayton is the historic birthplace of powered flight.

Dayton’s climate is classified as a humid continental climate. On average, there are 4.5 nights of sub-zero degrees Fahrenheit lows annually. Based on currentresults.com temperatures are coldest in January with highs around 36 degrees Fahrenheit and lows around 22 degrees. Snow is moderate, with a normal seasonal accumulation of 23.3 inches (59 centimeters) usually occurring from November to March.

It’s Easy to Add Affordable In-floor Heating From the Bathroom and Kitchen to Any Room in Your Home

Recent data on listing terms when selling a home uncovered some popular home features, among those heated/radiant floors. It makes sense that if people are looking to buy a home with these amenities, then existing homeowners should consider them when remodeling. WarmlyYours has an underfloor heating system for most any application and any room in your home. Here are some room examples along with compatible flooring selections.

No More Cold Bathroom Tile with Underfloor Heating

These Dayton homeowners needed to warm up the elegant but cold tile flooring in their newly remodeled bathroom, so they decided to add radiant floor heating to their medium master bath. Radiant heating is the perfect solution to bring welcoming warmth and luxury to your daily routine.

Cost per Square Foot of Radiant Warmth and Low Operating Cost Make This Bathroom Affordably Cozy

For their project, these owners selected a 1.5- by 38-foot TempZone

Flex Roll to install in their 70-square-foot bathroom. The cost was only $598.50 or $10.50 per square foot. In addition to the material cost, the operating cost should also be factored into the remodeling budget. WarmlyYours’ Operating Cost Calculator figures in the average kWh cost in Dayton of 11.79 cents resulting in a daily cost of 43 cents to heat this bathroom for four hours a day, a small price to pay for the comfort and luxury of a soothingly warm bathroom tile floor. Furthermore, the system can be the primary heating source for the room which is an additional cost and energy savings advantage.

Calculating Costs for Heating Up a Laminate Kitchen Floor

As their kitchen was one of the most used rooms in their home, these Dayton homeowners knew it made sense to add electric in-floor heating when planning their kitchen remodeling project.  To warm up the stylish but cold laminate flooring they had selected they chose to install an Environ Flex Roll floor heating system in the 123 square foot space for $860.00 at a cost of approximately $12.00 per square foot. The Flex Roll consists of an insulated heating cable sandwiched between two layers of reinforced, durable aluminum foil that radiates 12 watts per square foot.

Around 75 Cents a Day Will Heat This Kitchen Flooring

Factoring in the cost for operating the system is important when planning your budget. WarmlyYours has a useful online tool to help you do just that. Based on WarmlyYours’s Operating Cost Calculator it costs just 76 cents to heat this kitchen for eight hours a day. An added bonus is that this system can be a primary heat source for the room without incurring additional heating bills.  

TempZone

Cable Warms up this Office for Less than a Dollar a Day

This homeowner decided to install radiant heating during a recent remodeling of their home office to minimize the winter chill. The system was designed to heat the floors of their office with 300 feet (75 square feet) of 120-volt TempZone

Cable for $480.00. That amounts to just $6.40 per square foot. By adding a nHance programmable thermostat for $169, it brought the total to $649.00. 

Operating Cost is Low to Heat Underneath Wood Flooring

It’s important to consider the operating cost of your floor heating system when budgeting for your own project. WarmlyYours makes it easy for you with our Operating Cost Calculator. Based on the data from this tool, the cost to operate this system for 8 hours a day is just 46 cents. This calculator factors in the average kWh cost in Dayton, which is just slightly less than 12 cents. Best of all, this radiant heating system can be the primary heat source for the room so there’s no need for additional heating and higher energy bills.

Add a Basement Bedroom Complete with Radiant Floor Heating

These Dayton homeowners decided to add a basement bedroom for visiting friends and family, but were concerned about the cold basement floor. They discovered that electric radiant floor heating would be an ideal solution to that dilemma. They immediately ordered a WarmlyYours underfloor heating system for installation under new laminate flooring to keep the guest bedroom comfortably cozy during the winter rainy season.

Product Cost per Square Foot, Plus Operating Cost for the System

The 1.5- by 52-foot TempZone

flex roll fills 78 square feet of floor space and costs $741, which equates to just $9.50 per square foot. The flex roll is easy to cut and turn to effectively fill the floor space with 15 watts per square foot of soothing radiant heat. They were also pleasantly surprised to find that operating the in-floor heating is also affordable. According to WarmlyYours’ Operating Cost Calculator, it only costs 48 cents a day to heat this bedroom for eight hours.  The floor heating system can be the primary heat source for this room, so there won’t be any additional heating bills which is a welcome bonus.

Our Easy to Use Operating Cost Calculator Gives Cost To Run An In-floor Heating System

After you’ve chosen your floor heating system including how you’ll use it, you can calculate how much it will cost to operate. Actually, the calculating is done for you with the Operating Cost Calculator, a useful online tool that asks basic project questions; product type, room size, local energy rate and daily usage in order to calculate the daily, monthly and annual operating cost of your system. It’s simple to use.

To get started just use the calculator below:

Floor Heating Controls and Costs to Suit Your Lifestyle and Budget

Customize your comfort with the nSpiration series of thermostats from WarmlyYours. Each control has been tailored to meet a specific need.

From programmable models that allow you to easily monitor and manage your home comfort remotely from any device to controls where you can set it and forget it, all of our controls are designed to help you get the most out of your floor heating system. For large applications, or additional areas, you may have to combine the nJoin power module with your nSpiration Series thermostat.

nSpire Touch Wifi Programmable

Control your floor heating system with your smartphone or on the web with the nSpire Touch WiFi thermostat. The added ability to be controlled remotely can accommodate busy schedules. It also offers substantial energy savings without sacrificing comfort or convenience.  

nSpire Touch Programmable

It’s easy to set up a radiant heating system according to your preferences and schedule with the integrated Install Wizard included with the nSpire Touch. With 4 programmable events for each day of the week, the nSpire Touch allows you maximum control over the floor temperature.

nHance Programmable

You can easily set this control up for your exact needs and specifications with the nHance intuitive user-interface. For consistent schedules, it will deliver a maximum level of comfort when you need it most, like during your morning routine, while still keeping your overall energy use to a minimum.

nTrust Non-Programmable

Ease and reliability are benefits of the nTrust  thermostat. Because there is no programming required for the nTrust dual voltage (120V/240V) control, you can just set it for your desired temperature and then sit back and relax. 

Radiant Floor Heating Technical Installation Support Available 24/7

Our 24/7 technical support experts will be on hand to guide you every step of the way through your installation, whenever you need assistance. Ensuring your project goes smoothly is WarmlyYours commitment to you, so whenever you are ready to install your system, we will be there for you day or night.

Get Started Quickly with our Radiant Heat Cost Calculator and SmartPlan

Using our Radiant Heat Cost Calculator is the easiest way to plan for adding electric floor heating to your next project. All you need to do is fill in some basic information about your project and the cost calculator tool will give you a side-by-side comparison of the recommended products and costs for your room. Using this tool allows you to plan and budget for your own project online. Get started right now by clicking here.   

The next step is to upload a floor plan of your room to get your radiant heating SmartPlan

. This plan provides more in-depth detail than a radiant heat cost calculator because it shows exactly how the floor-heating system should be laid out with the electrical plan. This custom SmartPlan

helps ensure an easier install by helping our expert technical staff guide you through the complete installation process.

If you have any questions, there are several ways you can reach us. 1) Call us at 800-875-5285, 2) live chat us at http://www.warmlyyours.com, or 3) email us sales@warmlyyours.com. Whether you live in Dayton or another city that could benefit from our radiant heating solutions, WarmlyYours is ready and waiting.

Skyline image: By MarkDonna at the English language Wikipedia, CC BY-SA 3.0, https://commons.wikimedia.org/w/index.php?curid=2502958

Source: https://www.warmlyyours.com/en-US/posts/how-much-does-floor-heating-cost-in-dayton-oh

source https://warmlyyours1.wordpress.com/2018/05/01/how-much-does-floor-heating-cost-in-dayton-oh/

[atlasbutler]

July is usually the month in Columbus when temperatures and humidity are at their peaks. Here are 6 creative ways to easily stay cool this summer.

[ohioelectricityrates]

Cut High Columbus Energy Bills With Smart Thermostats

New Post has been published on http://www.ohenergyratings.com/blog/2018/05/02/cut-high-columbus-energy-bills-smart-thermostats/

Cut High Columbus Energy Bills With Smart Thermostats

Columbus electricity customers can save on their energy bills year ‘round when they install a smart thermostat with a great rebate from AEP!

Want to save money on a smart thermostat with your electric company in Columbus?

Smart shoppers in Columbus know there are more ways to save on your energy bill than finding the cheapest electricity rate. A great option to save energy and money is installing a smart thermostat. But with the prices for these thermostats running a bit higher than standard programmable thermostats, it pays to look for incentives and rebates before you buy!

What are your options to save money on a smart thermostat?

Don’t pay full price on a smart thermostat for your home when you have options to save!

In the AEP Ohio Power service area, you have access to a rebate up to $100 on smart thermostats. You’ll need to have residential service established through AEP Ohio Power Company and rebate amounts depend on whether you use gas or electric to heat your home.

How do smart thermostats help you save on your high energy bill in Columbus?

Many homeowners know they can save money by changing thermostat settings, but tend to forget to actually do it, missing opportunities to save on their AEP electric bill. Smart thermostats change settings automatically to save you money; some can even learn your schedule and tendencies for even greater savings.

A popular smart thermostat brand, Nest, uses an online savings calculator to predict how much you can save. According to the calculator, the average household in Columbus can expect to save about $100 a year.

Other competitive options for smart thermostat brands include Ecobee and Honeywell. With Energy Star Ratings and money saving features, products from any of these manufacturers should be eligible for rebates through AEP.

Another nifty feature of a smart thermostat is the ability to control settings remotely with an app on your phone. For example, if you leave the house for the weekend and forget to turn down the heat, you can access the thermostat, lower your temperature settings further, and save a bundle!

Use Ohio Energy Ratings to compare AEP Suppliers and save even more!

Because you have the power to choose your energy supplier in Columbus, why not choose an option with an incentive for smart thermostats? If you decide to switch electric companies, find the best electric company for you with an apples-to-apples comparison of PUCO suppliers and available plans.

Anytime you need to save money on electricity, shop for the cheapest price at Ohio Energy Ratings. Get more tips to save on your energy bill in Columbus here.