#ENC28J60

[jayakody2000lk]

STM8S005C6T6 Ethernet development board

In this project, we built an STM8S005C6T6 based Ethernet development board for our IoT experiments. This development board consists of ENC28J60, 10BASE-T stand-alone Ethernet controller, CH340G, USB serial interface, 2 LED indicators, and passive buzzer unit.

The firmware framework for this development board has been developed using SDCC. To enable IPv4 support, we convert the EtherCard driver, which is available for the Arduino platform. The current version of this driver supports all other EtherCard functions except TCP support.

In the given design, the SPI terminals of the MCU are connected to the ENC28J60 Ethernet controller. All SPI terminals, such as MISO / PC7, MOSI / PC6, and SCK / PC5, are connected directly to the Ethernet controller. In addition, the PC4 terminal of the MCU is used as ENC28J60, CHIP-SELECT.

The CH340G USB serial interface is connected to the UART2 terminals of the MCU. In STM8S005C6T6, the UART2 is mapped to the PD6 and PD5 terminals of the MCU. The USB interface of this development board consists of the jack-sense feature. The jack-sense status can access from PD7.

The minor peripherals such as LED indicators and buzzer are connected to the PORTD of the MCU. The LED indicators are connected to terminals PD0 and PD1 and can be activated or deactivated via jumpers. The passive buzzer is connected to PD4 and can run through the STM8 beep sound generator unit.

All peripherals of this development board are powered by a 3.3V supply. The recommended supply voltage for this development board is 5V to 9V.

In addition to the STM8S005C6T6, this development board supports the following STM8 series, LQFP48 packaged microcontrollers: STM8S007C8T6, STM8S207C8T6, and STM8S105C6T6.

All the resources of this development board are available at the GitHub project repository. The supplied firmware is developed and tested with SDCC version 3.8 on a Linux environment. Before compiling and flashing the MCU, make sure to install the stm8flash application on the system. The supplied makefile use this application to program the fuses and flash memory of the MCU.

The schematic and PCB design of this project is released under the terms of CERN-OHL-W Version 2.0. The firmware framework is released under the terms of the GNU GPL 2.0 license.

[manish12jugran-blog]

Ubidots + ESP32- Predictive Machine Monitoring

Predictive analysis of machine vibration and temp by creating mail events and a record of vibration in google sheet using Ubidots.

Story

Predictive Maintenance and Machine Health Monitoring

The rising of new technology i.e, the Internet of Things, heavy industry has started adopting sensor-based data collection to solve its biggest challenges, principal among them process downtime in the form of shutdowns and process delays. Machine monitoring also called predictive maintenance or condition monitoring is the practice of monitoring electrical equipment through sensors in order to accumulate diagnostic data. To achieve this, data acquisition systems and data loggers are used to monitor all kinds of equipment, such as boilers, motors, and engines. Following condition are measured:

Temperature and Humidity Data Monitoring

Current and Voltage Monitoring

Vibration Monitoring: In this article, we will read Temperature, vibration and publish the data in Ubidots. Ubidots supports graphs, UI, notifications, and emails. These features make it ideal for predictive maintenance analysis. We will also get the data in google sheets which will make predictive maintenance analysis more easier.

Hardware:

ESP-32

IoT Long Range Wireless Vibration And Temperature Sensor

Long-Range Wireless Mesh Modem with USB Interface

Software Used:

Arduino IDE

Ubidots

LabView Utility

Library Used:

PubSubClient Library

Wire.h

Arduino Client for MQTT

This library provides a client for doing simple publish/subscribe messaging with a server that supports MQTT

For more information about MQTT, visit mqtt.org.

Download

The latest version of the library can be downloaded from GitHub

Documentation

The library comes with a number of example sketches. See File > Examples > PubSubClient within the Arduino application.Full API Documentation.

Compatible Hardware

The library uses the Arduino Ethernet Client api for interacting with the underlying network hardware. This means it Just Works with a growing number of boards and shields, including:

Arduino Ethernet

Arduino Ethernet Shield

Arduino YUN – use the included YunClient in place of EthernetClient, and be sure to do a Bridge.begin() first

Arduino WiFi Shield - if you want to send packets greater than 90 bytes with this shield, enable the MQTT_MAX_TRANSFER_SIZE () option in PubSubClient.h.

Sparkfun WiFly Shield – when used with this library

Intel Galileo/Edison

ESP8266

ESP32The library cannot currently be used with hardware based on the ENC28J60 chip – such as the Nanode or the Nuelectronics Ethernet Shield. For those, there is an alternative library available.

Wire Library

The Wire library allows you to communicate with I2C devices, often also called "2 wire" or "TWI" (Two Wire Interface), can download from Wire.h

Basic Usage

Wire.begin()Begin using Wire in master mode, where you will initiate and control data transfers. This is the most common use when interfacing with most I2C peripheral chips.

Wire.begin(address)Begin using Wire in slave mode, where you will respond at "address" when other I2C masters chips initiate communication.

Transmitting

Wire.beginTransmission(address)Start a new transmission to a device at "address". Master mode is used.

Wire.write(data)Send data. In master mode, beginTransmission must be called first.

Wire.endTransmission()In master mode, this ends the transmission and causes all buffered data to be sent.

Receiving

Wire.requestFrom(address, count)Read "count" bytes from a device at "address". Master mode is used.

Wire.available()Returns the number of bytes available by calling receive.

Wire.read()Receive 1 byte.

Steps to send data to Labview vibration and temperature platform using IoT long-range wireless vibration, temperature sensor and long-range wireless mesh modem with USB interface:

First, we need a Labview utility application which is ncd.io Wireless Vibration and Temperature Sensor.exe file on which data can be viewed.

This Labview software will work with ncd.io wireless Vibration Temperature sensor only

To use this UI, you will need to install following drivers Install run time engine from here 64bit

32 bit

Install NI Visa Driver

Install LabVIEW Run-Time Engine and NI-Serial Runtime

Getting started guide for this product.

Uploading the code to ESP32 using Arduino IDE:

Download and include the PubSubClient Library and Wire.h Library.

You must assign your unique Ubidots TOKEN, MQTTCLIENTNAME, SSID (WiFi Name) and Password of the available network.

Compile and upload the Ncd__vibration_and_temperature.ino code.

To verify the connectivity of the device and the data sent, open the serial monitor. If no response is seen, try unplugging your ESP32 and then plugging it again. Make sure the baud rate of the Serial monitor is set to the same one specified in your code 115200.

Serial Monitor Output:

Data on serial monitor of Arduino IDE.

Making the Ubidot Work:

Create the account on Ubidot.

Go to my profile and note down the token key which is a unique key for every account and paste it to your ESP32 code before uploading.

Add a new device to your Ubidot dashboard name ESP32.

Now you should see the published data in your Ubidots account, inside the device called "ESP32".

Inside the device create a new variable name sensor in which your temperature reading will be shown.

Now you are able to view the Temperature and other sensors data which was previously viewed in the serial monitor. This happened because the value of different sensor readings is passed as a string and store in a variable and publish to a variable inside device esp32.

Create a dashboard in ubidots.

Go to data select dashboard and inside dashboard create different widgets and add a new widget to your dashboard screen.

OUTPUT

Now as the temperature/vibration increases and decreases new data available inside the various variable.

Creating Events in Ubidots

1) Select Events (from the Data dropdown).

2) To create a new event, click the yellow plus icon in the upper right corner of the screen.

Types of Events: Ubidots support already integrated events to allow you to send Events, Alerts, and Notifications to those who need to know when they need to know. Ubidots' prebuilt integrations include:

Email notifications

SMS notifications

Webhook events - learn more

Telegram notifications

Slack notifications - learn more

Voice Call notifications - learn more

Back to Normal notification - learn more

Geofence notifications - learn more

3) Then choose a device and associating variable that indicates the devices' "values".

4) Now select a threshold value for your event to trigger and compare it to device values and also select time to trigger your event.

5) Establish and configure which actions are to be executed and the message to the receiver: Send SMS, Email, Webhooks, Telegrams, Phone Calls, SLACK, and webhooks to those who need to know.

6) Configure the Event notice.

7) Determine the activity window the events may/may not be executed.

8) Confirm your Events.

The output of Event in Your Mail:

Export Your Ubidots Data to Google Sheets:

In this, we can extract the data stored in the Ubidots cloud for further analysis. The possibilities are enormous; for instance, you could create an automatic report generator and send them to your customers every week.

Another application would be device provisioning; if you have thousands of devices to deploy, and their information is in a Google Sheet, you could create a script to read the sheet and create a Ubidots data source for every line on the file. Steps to do this-

Create a Google Sheet and add two sheets to it with these names:

 Variables

Values

From your Google Sheet, click on "Tools" then "Script Editor...", then "Blank Project".

Open the Script Editor.

Add the code below (in the code section) to the script Script.

Done! now open your Google Sheet again and you'll see a new menu to trigger the functions.

Result:

[cocewaykixsde]

ENC28J60 LAN Ethernet Network Board Module For Arduino 25MHZ Crystal AVR 51 LPC STM32 3.3V

ENC28J60 LAN Ethernet Network Board Module For Arduino 25MHZ Crystal AVR 51 LPC STM32 3.3V

lastest_volume

0

Just For Today

Click Here To Visit The Shop

N€W ENC28J60 LAN Ethernet Network Board Module For Arduino 25MHZ Crystal AVR 51 LPC STM32 3.3V

[anakkendali]

Arduino, Cara Mendapatkan IP Ethernet ENC28j60 dari Laptop

[3d-printer-store-uk]

ENC28J60 ENC28J60-I/SO HR911105A Ethernet LAN Network Module SPI Interface 3.3V for Arduino AVR PIC LPC STM32

The article was originally published here!

[chhatramani]

Web-Based Water-Level Monitor and Pump Controller | Full DIY Project

Web-Based Water-Level Monitor and Pump Controller | Full DIY Project

Web-Based Water-Level Monitor and Pump Controller

Several articles about water-level controllers for overhead tanks have been published in earlier issues of EFY magazine. But the project we are going to share today is new and unique. So presented here is a Web-based water-level monitor and motor-pump controller using ATmega128 microcontroller, Ethernet controller ENC28J60 and TCP-IP protocol.…

[actualdriversshopy4f-blog]

DOWNLOAD CV PERSONAL STATEMENT HGV DRIVER

Date Added: 29 November, 2019 File Name: cv personal statement hgv driver Uploader: Prize Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X File Size: 23 Mb Downloads: 7348 Download Type: http File Version: 213131019 Price: Free File Format: exe

Bug fix: - Fixes D2D function abnormal when insert non HDD device and set it boot order 1st. - Fixed(cv personal statement hgv driver Fixed) wrong display of CPU2 information during POST. - Video playerFixed the(cv personal statement hgv driver the) error of .mp4 playback. - Fixes PS/2 KB&MS sometime can't wakeup from S1. - Fixed LED behavior(cv personal statement hgv driver behavior) when disable wifi. - Fixed PPPoE issue after DUT power off. - Fixes an issue where the Microsoft Windows Wireless(cv personal statement hgv driver Wireless) LAN 802.11 Extensibility Framework stops working in an ad-hoc operation with WPA2-AES security. - Modified to sort timezone settings in the order of UTC. - Fixed a bug where the product information was not displayed correctly. - Fixed the(cv personal statement hgv driver the) text display issue. - Quotas] Fixed a bug where up to 2047 GB were allocated as the quota size. Users content: The Witcher 3: Wild Hunt may experience stuttering during gameplay. Add authentication to CGI /config/stream_info.cgi. Copy the file M2100A00. BIOS can't be update if the build date of new chosen BIOS is equal or early to original. InstallationSimply run the SystemMonitor. This file extracts to your hard drive and is placed in a folder that begins with C:\epson\epson12258... Switch connection types, and alter the settings of your connection on this page. This installer contains:Encoder and Parental Control. Improvement on Administrator password. GER/CHS Inconsistent translation in Quick Set Power management wizard Other Changes/Addtions:-------------------------------1. Click to find the DOWNLOAD AVR ENC28J60 DRIVER. Supported OS: Microsoft Windows 8.1 Pro (64-bit) Windows Server 2008 R2 Windows 7 64-bit Windows Server 2016 Windows Server 2012 Windows 8.1/8/7/Vista 32-bit Microsoft Windows 8.1 (32-bit) Windows Vista 32-bit Notebook 8.1/8/7 32-bit Microsoft Windows 8.1 Pro (32-bit) Microsoft Windows 8.1 (64-bit) Windows 10 Windows 7 32-bit Microsoft Windows 10 (32-bit) Microsoft Windows 8.1 Enterprise (32-bit) Windows Server 2003 64-bit Microsoft Windows 8 Pro (64-bit) Windows 7 Windows 8.1 Microsoft Windows 10 (64-bit) Windows 2000 Microsoft Windows 8 Pro (32-bit) Microsoft Windows 8.1 Enterprise (64-bit) Windows Server 2012 R2 Microsoft Windows 8 (64-bit) Notebook 8.1/8/7 64-bit Windows Server 2008 Microsoft Windows 8 Enterprise (32-bit) Windows 8.1/8/7/Vista 64-bit Windows XP 64-bit Microsoft Windows 8 (32-bit) Windows Server 2003 32-bit Windows Vista 64-bit Windows 8 Microsoft Windows 8 Enterprise (64-bit) Windows XP 32-bit Searches: personal hgv statement driver cv; cv personal statement hgv CWKSE3290; cv personal statement hgv CW3290; cv personal statement hgv C CW329-3; cv personal statement hgv driver for Windows Server 2012; cv personal statement hgv driver for Windows 7; cv personal statement hgv driver for Windows XP 32-bit; cv personal statement hgv C32m; cv personal statement hgv driver for Windows 7 64-bit; cv personal statement hgv Cmb329-mbj; cv personal statement hgv driver for Windows Vista 32-bit Compatible Devices: Ipad; Usb Cables; Soundcard; Keyboards; Monitor; Printer To ensure the integrity of your download, please verify the checksum value. MD5: a08654076a5791f45ea6095df5b30c22 SHA1: 805318145102fc98eab1767a3bc38b9c92a58285 SHA-256: cfbb6a8c06f867c5bc4bfb01bc013ab7848d3e0451e00e000abac12b2f092020

[proj-eletronicos]

👉 Waldunano com adaptador de rede cabeada. Mais um device para agregar a essa super placa. IOT também se faz com rede cabeada !!! 😎 . #Waldunano #rede #cabeada #iot #internet #projeto #Ethernet #shield #Enc28j60  #arduino #arduinouno #arduinomega #makers #maker #diy #geek #tcc #projetos #eletrônica #hardwae #walproj #projetoseletronicos #projetosmaker #diyprojects https://www.instagram.com/p/BwYZD6UhYiO/?utm_source=ig_tumblr_share&igshid=1btqcb6829pr9

[jayakody2000lk]

NTP based digital clock panel driver

This project introduces an open-source, ATmega328 based, configurable NTP clock with a 2.3-inch, 7-segment display driver. This clock automatically obtains time from the configured NTP server and updates the date and time of the built-in RTC (real-time clock). If the connection to the NTP server is lost, the clock continues to run using its built-in RTC.

All the parameters of this clock can configure using its USB base serial terminal. The firmware of this clock supports both static and DHCP addressing modes. Apart from that, parameters such as NTP server address, time-offset, and clock display formats can change through the menu-driven configuration terminal. This clock is designed to drive large common-anode, 7-segment displays. The prototype version is assembled using four individual segments of 7.2V, 2.3-inch, red color displays (FJS23101BH). To archive, the necessary high output voltage and the current, the 7-segment display output stage of this clock is formed using ULN2803 Darlington transistor array and BC858 transistors. The network component of this clock is built around the ENC28J60 10BASE-T stand-alone Ethernet controller.

Highly accurate DS3231M RTC is using in this clock for time-keeping operations. To backup the date and time, the CR1220 type button cell is included in the PCB. The date and time are syncs with the NTP server during the system startup. Users can manually initiate synchronization by pressing the "SYNC" button in the system. Depending on the NTP server, the user needs to specify the time offset to the system to get the correct local time. Time offset can configure using the system configuration menu, and it must be input in a standard format like +5:30. Firmware of this clock is developed using the Arduino framework and libraries. PCBWay provides sponsorship for this project. The PCBWay online ordering service provides excellent help to fabricate this PCB. We got finished PCBs within three days, and the quality of the service is at a superior level. PCB of this project can directly order from PCBWay through this link.

This project is an open hardware project. All the project source codes, schematic diagrams, documentation, PCB designs, and compiled firmware files are available in the project GitHub repository.

[manish12jugran-blog]

ThingSpeak, IFTTT, Temp and Humidity Sensor and Google Sheet

Story

In this project, we will measure temperature and humidity using NCD temperature and humidity sensor, ESP32, and ThingSpeak. We will also send different temperature and humidity readings to Google Sheet using ThingSpeak and IFTTT for analyzing the sensor data.

Hardware

ESP-32: The ESP32 makes it easy to use the Arduino IDE and the Arduino Wire Language for IoT applications. This ESP32 IoT Module combines Wi-Fi, Bluetooth, and Bluetooth BLE for a variety of diverse applications. This module comes fully-equipped with 2 CPU cores that can be controlled and powered individually, and with an adjustable clock frequency of 80 MHz to 240 MHz. This ESP32 IoT WiFi BLE Module with Integrated USB is designed to fit in all ncd.io IoT products. Monitor sensors and control relays, FETs, PWM controllers, solenoids, valves, motors and much more from anywhere in the world using a web page or a dedicated server. We manufactured our own version of the ESP32 to fit into NCD IoT devices, offering more expansion options than any other device in the world! An integrated USB port allows easy programming of the ESP32. The ESP32 IoT WiFi BLE Module is an incredible platform for IoT application development. This ESP32 IoT WiFi BLE Module can be programmed using the Arduino IDE.

IoT Long Range Wireless Temperature and Humidity Sensor: Industrial Long Range Wireless Temperature Humidity Sensor. Grade with a Sensor Resolution of ±1.7%RH ±0.5°C. Up to 500, 000 Transmissions from 2 AA Batteries. Measures -40°C to 125°C with Batteries that Survive these Ratings.Superior 2-Mile LOS Range & 28 miles with High-Gain Antennas.Interface to Raspberry Pi, Microsoft Azure, Arduino and More

Long-Range Wireless Mesh Modem with USB Interface

Software Used

Arduino IDE

ThingSpeak

IFTTT

Library Used

PubSubClient Library

Wire.h

Arduino Client for MQTT

This library provides a client for doing simple publish/subscribe messaging with a server that supports MQTT

For more information about MQTT, visit mqtt.org.

Download

The latest version of the library can be downloaded from GitHub

Documentation

The library comes with a number of example sketches. See File > Examples > PubSubClient within the Arduino application. Full API Documentation.

Compatible Hardware

The library uses the Arduino Ethernet Client API for interacting with the underlying network hardware. This means it Just Works with a growing number of boards and shields, including:

Arduino Ethernet

Arduino Ethernet Shield

Arduino YUN – use the included YunClient in place of EthernetClient, and be sure to do a Bridge.begin() first

Arduino WiFi Shield - if you want to send packets greater than 90 bytes with this shield, enable the MQTT_MAX_TRANSFER_SIZE option in PubSubClient.h.

Sparkfun WiFly Shield – when used with this library

Intel Galileo/Edison

ESP8266

ESP32The library cannot currently be used with hardware based on the ENC28J60 chip – such as the Nanode or the Nuelectronics Ethernet Shield. For those, there is an alternative library available.

Wire Library

The Wire library allows you to communicate with I2C devices, often also called "2 wire" or "TWI" (Two Wire Interface), can download from Wire.h

Basic Usage

Wire.begin()Begin using Wire in master mode, where you will initiate and control data transfers. This is the most common use when interfacing with most I2C peripheral chips.

Wire.begin(address)Begin using Wire in slave mode, where you will respond at "address" when other I2C masters chips initiate communication.

Transmitting

Wire.beginTransmission(address)Start a new transmission to a device at "address". Master mode is used.

Wire.write(data)Send data. In master mode, beginTransmission must be called first.

Wire.endTransmission()In master mode, this ends the transmission and causes all buffered data to be sent.

Receiving

Wire.requestFrom(address, count)Read "count" bytes from a device at "address". Master mode is used.

Wire.available()Returns the number of bytes available by calling receive.

Wire.read()Receive 1 byte.

Uploading the Code to ESP32 using Arduino IDE

Before uploading the code you can view the working of this sensor at a given link.

Download and include the PubSubClient Library and Wire.h Library.

You must assign your API key, SSID (WiFi Name) and Password of the available network.

Compile and upload the Temp-ThinSpeak.ino code.

To verify the connectivity of the device and the data sent, open the serial monitor. If no response is seen, try unplugging your ESP32 and then plugging it again. Make sure the baud rate of the Serial monitor is set to the same one specified in your code 115200.

Serial Monitor Output

Output

Create an IFTTT Applet

To send data to ThingSpeak you can view it at this link.

IFTTT is a web service that lets you create applets that act in response to another action. You can use the IFTTT Webhooks service to create web requests to trigger an action. The incoming action is an HTTP request to the webserver, and the outgoing action is an email message.

First, create an IFTTT account.

Create an applet. Select My Applets.

Click the New Applet button.

Select the input action. Click the word this.

Click the Webhooks service. Enter Webhooks in the search field. Select the Webhooks.

Choose a trigger.

Complete the trigger fields. After you select Webhooks as the trigger, click the Receive a web request box to continue. Enter an event name.

Create trigger.

Now the trigger is created, for resulting action click That.

Enter “Google Sheets” in the search bar, and select the “Google Sheets” box.

If you have not connected to Google Sheet, then connect it first. Now choose action. Select add a row to a spreadsheet.

Then, complete the action fields.

Your applet should be created after you press the Finish.

Retrieve your Webhooks trigger information. Select My Applets, Services and search for Webhooks. Click Webhooks and Documentation button. You see your key and the format for sending a request. Enter the event name. The event name for this example is VibrationAndTempData.You can test the service using the test button or by pasting the URL into your browser.

Create a MATLAB Analysis

You can use the result of your analysis to trigger web requests, such as writing a trigger to IFTTT.

Click Apps, MATLAB Analysis and select New.

Select Trigger Email from IFTTT in the Examples section. The code below is prepopulated in your MATLAB analysis window.

Name your analysis and modify the code.

Save your MATLAB Analysis.

Create a Time Control to Run Your Analysis

Evaluate your ThingSpeak channel data and trigger other events.

Click Apps, TimeControl, and then click New TimeControl.

Save your TimeControl.

Output

[liuxing168]

High-priced recycling MICROCHIP chips, full series and full models, long-term online procurement of factory inventory IC chips, company's personal project surplus chips, integrity and formality, high professional price ATMEGA328P-AU

ATMEGA2560-16AU

PIC18F4620-I/PT

PIC32MX575F512L-80I/PT

ATMEGA644PA-AU

MCP23S17-E/SS

KSZ9031RNXIC

ATMEGA128A-AU

PIC18F46K22-I/PT

ATMEGA8A-AU

25LC512-I/SN 

PIC16F1938-I/SS

PIC18F8722-I/PT

ATMEGA64A-AU

ATMEGA328P-PU

ATMEGA32A-AU

DSPIC33EP512MU810-I/PT

ATMEGA16A-AU

PIC18F4685-I/PT

PIC32MX795F512L-80I/PT

PIC18F45K22-I/PT

PIC16F1939-I/PT

PIC32MX795F512L-80I/PF

DSPIC30F5011-30I/PT 

PIC18F46K80-I/PT

MCP23017-E/SS

24LC64T-I/SN

ENC28J60-I/SS

ATMEGA88PA-AU

ATMEGA1284P-AU

ATMEGA168PA-AU

ATMEGA8L-8AU

AT90CAN128-16AU

ATMEGA328P-MU

PIC16F887-I/PT 

MCP4728-E/UN

PIC18F25K22-I/SS 

PIC18F4680-I/PT 

PIC12F675-I/SN ATMEGA328PB-AU PIC16F1823-I/SL  24LC256T-I/SN AT24C02C-SSHM-T

PIC18F25K22-I/SO  ATXMEGA128A1-AU

PIC18F4520-I/PT ATXMEGA128A1U-AU ATMEGA8515-16AU  MCP2515-I/SO MCP1702T-3302E/CB 

24LC16BT-I/SN AT89C51RD2-SLSUM 

LAN8720AI-CP-TR AT24C64D-SSHM-T

MCP23S17-E/SO KSZ8863RLLI  ATMEGA2561-16AU AT24C256C-SSHL-T LAN8720A-CP-TR KSZ8863RLL  ATMEGA48PA-AU DSPIC33FJ256MC710A-I/PT  KSZ8895MQXIA ATMEGA32U4-AU  PIC16F1937-I/PT MCP23017-E/SO PIC16LF1829-I/SO PIC18F6722-I/PT 24LC256-I/SN PIC18F67K22-I/PT ATMEGA128-16AU 24LC64-I/SN PIC16F1829-I/SS MCP4728T-E/UN  ATMEGA644P-20AU  ATXMEGA128A4U-AU MCP4725A0T-E/CH

PIC18F66K80-I/PT MCP6002T-I/SN

MCP7940N-I/SN PIC18F26K22-I/SS ATXMEGA256A3-AU  PIC18F2420-I/SO ATMEGA32U4-MU 25LC1024-I/SM  KSZ8995MAI  USB2514BI-AEZG  ATXMEGA32A4U-AU  PIC12F1822-I/SN  ATSAM3X8EA-AU PIC18F6520-I/PT  PIC16F676-I/SL  MCP2515-I/ST PIC18F2520-I/SO  AT24C512C-SSHD-T  AT25256B-SSHL-T AT91SAM7S256D-AU PIC16F688-I/SL

MIC2026-1YM  KSZ8863MLL 

[vinafetphcm]

Module Ethernet ENC28J60

[yourrobotplace-blog]

For just €5.24 Application: Computer Operating Temperature: 1 Condition: New Dissipation Power: 1 Brand Name: TENSTAR ROBOT Supply Voltage: 1 Type: Voltage Regulator Package: DIP Model Number: module is_customized: Yes

[teknorehberimm]

Arduino ile Sunucuya Veri Göndermek

Arduino; sensörlerden gelen sinyalleri okumak, motor kontrolü, led yakıp söndürmek gibi elektronik uygulamaların kolayca kullanılması için geliştirilen açık kaynaklı fiziksel programlama platformudur. Arduino C programlama dili ile benzer yapıdadır. Eğer C biliyorsanız zorlanmadan Arduino işlemlerini de yapabilirsiniz.

Bu yazımızda sensörler vb. ile elde edilen veriyi Arduino ile sunucuya göndermek ve sunucudaki bu verilerle bir web sayfasında oluşturmayı anlatacağız.

Öncelikle bilgisayarınızda bir sanal sunucu kurulu olmalı. Wampserver, EasyPHP, XAMPP gibi birçok alternatiften dilediğinizi kullanabilirsiniz. Veritabanı işlemlerini bu sanal sunucu ile yapacağız.

Bu anlatımda arduinonun internet bağlantısını sağlamak için ENC28J60 ethernet lan modülünü kullanacağız. Siz farklı bir modülde kullanabilirsiniz. ENC28J60 için gerekli kütüphane dosyalarını Github’dan edinebilirsiniz.

Sanal sunucudaki veritabanına veri göndermek için bir veri kaynağına ihtiyacımız olacak. Bu yazıda DS18B20 kullanıyoruz. DS18B20 için gereken kütüphane Onewire. Siz farklı bir veri kaynağı ve buna uygun bir kütüphane tercih edebilirsiniz.

Alttaki görselde sıcaklık sönsörü ve Ethernet modülünün Arduino bağlantısını görebilirsiniz.

Bağlantıyı uygun şekilde yaptıysanız artık veritabanı işlemlerine başlayabiliriz. Öncelikle sanal sunucunuzdaki phpmyadmine bağlanın ve alttaki kodları çalıştırarak bir veritabanı oluşturun.

Veritabanı ile bağlantı kurabilmek için sunucu ana dizininde mysql.php isimli bir dosya oluşturun ve alttaki kodları ekleyin ve kaydedin.

Veritabanı ile bağlantı kurduk. Artık iş son aşamaya geldi. Verileri görüntüleyebilmek için bir sayfa oluşturmamız gerekiyor. Yine anadizinde index.php isimli bir dosya oluşturacak ve verileri göstermek için gereken kodları yazacağız. Bu aşamadan sonra veritabanına veri eklemek için gereken php dosyasını oluşturma ve son olarak arduino için gereken kodları yazmak kalıyor.

Arduino ile sunucuya veri gönderme anlatımı için yazarının izni ile teknotezgah.com’da yayınlanan makaleden faydalanılmıştır. Kalan adımları alttaki kaynak linkinden okuyabilir ve gerekli tüm kaynak dosyalarına yine bu adresten ulaşabilirsiniz. Umarım faydalı olmuştur.

Kaynak: https://teknotezgah.com/arduino-ile-sunucuya-veri-gonderme/

İçeriğin devamı ve görsellerini kaynak linkten görüntüleyebilirsiniz.

[androidpimp]

New Post has been published on

New Post has been published on http://www.androidpimp.com/add-on-boards/raspberry-pi-zero-board-lan-adapter-expansion-board/

Raspberry Pi Zero Board LAN Adapter Expansion Board

Product Introduction

Raspberry Pi Zero Board hobbyists will be happy to know that 52Pi launched a new GeeekPi Enc28j60 Network Adapter Module adding LAN connectivity support to the board. This add-on board for the Raspberry Pi Zero mini computer makes connecting your Pi Zero to the Internet via Ethernet super simple. If you’re fed up with unstable WiFi signal and want your Pi Zero to be online all the time, then this is a good solution for custom DIY projects.

The Enc28j60 Network Adapter is a neat little board with an Ethernet controller and standard RJ45 connectors so you can hook your Pi up to your home or office network using standard Ethernet cables. There are no special software or drivers to install. It works right out of the box with Raspbian – simply attach to your Pi’s GPIO header and you are ready to go.

Official GeeekPi Amazon Store

Official GeeekPi Aliexpress Store

  Raspberry Pi Zero Board LAN Adapter Add-on By 52Pi

Main Highlights:

It is very easy to assemble and configure.

Supports up to Ethernet speed (10Mbps).

Uses the Pi Zero’s GPIO pins, your USB connector is still free for something else!

For Pi Zero Generation, no NIC is inconvenient, because its core system is Linux.

It allows your Raspberry Pi zero to access the network smoothly, and it is easy to do system updates and software installation operations.

  Package Content:

1x Enc28j60 network adapter module

1x Instruction Manual

[pccareus]

3Pcs ENC28J60 Ethernet Shield Network Module V1.0 For Arduino Nano | eBay https://buff.ly/2Bx5zRt