ubtvsig - Tumblr blog

[ubtvsig]

Is Purchasing Direct TV Satellite Signal Finder The Right Decision?

As suggested by the name, the direct TV satellite signal finder or the satellite director, or the dish pointer, is a handheld device that has been designed for tuning or locating the television satellites. It is quite helpful when one is looking to get a better signal for their dish. However, at times the satellite finder wouldn’t work if one is trying to aim the current DirectTV Dish. Now, it might work right with the round dish or the non-SWM HD dish. However, if SWM has been built in the dish itself, the satellite finder can leave the users quite frustrated and without the picture on the TV.

What is Special About the DirectTV SWM?

The satellite system of DirectTV has been designed to remain different from the satellite systems that are used all throughout the world. It is also quite different from the 1990s’ original system of DirectTV. It is because it is meant to help the users save a lot of money.

DirectTV became successful with people wanting to have a bigger and bigger system, which took a huge amount of wire. Well, unlike the cable TV system, the original system of DirectTV needed the wire from the dish for literally every single television. Furthermore, increased number of homes started coming pre-wired for the cable, and these weren’t possible to be used for the DirectTV as they had the splitters and the single cable which came into the house.

With DirectTV rolling out the HD service in the late 2000s, they came in with SWM or the Single-Wire Multiswitch. This had the tech which could put all of the needed signals for running every single receiver in the home on a single wire.

Now, this cannot be used with the cable television splitters as it is quite a similar type of tech that supports just one wire in the house, and it has much simpler wiring. However, it also means that the direct tv satellite finder doesn’t work herein.

Why wouldn’t it work?

The direct tv satellite signal finder is quite a simple audio receiver. It features the look of the L-band signal that gets produced through the satellite dish, which is based on the Ku-band signal, which is received from the primary satellite of the DirectTV. If it ‘hears’ the same, you will be able to see the meter move. Not more is there to it. It is unfortunate that the SWM tech operates quite differently.

The SWM technology of DirectTV relies on the receiver to request the signal before it is provided. Further, when the same is provided, it can get used with any of the eight different kinds of frequencies. So, the simple satellite finder, it doesn’t know what it has to do with the information if it would hear, and it also doesn’t know how it can be requested. For the fancy stuff, one will need the meter that comes with the DirectTV Advanced Installation Meter, and it can be a little more expensive. However, it does earn up the money and allows the user to zero in on signals from varied types of dishes like that of the SWM-enabled dish of DirectTV. It will help one to get the dish set up, so as to ensure that one can get down to watch what exactly the user wants.

Is the direct TV satellite signal finder not good for anything?

The solid signal satellite finder will still work for aiming the legacy dishes that don’t have the SWM tech built in there. In case one has more than 1 wire that comes out from the dish, the meter will be working right. One can even use it for most of the Dish equipment. For sure, it will come with a simpler analog meter, and it wouldn’t help one to get best of the possible aim on the satellite. However, on the other hand, being one of the simple portable devices that wouldn’t take any power to run, and it is nice to have the same in the tool kit.

So, if you are looking for one of the direct tv satellite signal finder, connect with UBTVSIG to get the best UMDS-LED model device. It doesn’t just have excellent sensitivity but also has the in-line IF signal strength meter and the best LED display. Just connect with us through our website, and we will help you out from there.

View Source:- https://medium.com/@ubtvsig/is-purchasing-direct-tv-satellite-signal-finder-the-right-decision-d749c34b60a2

Read Our One More Blog: How does a TV 3 Way Coax Splitter Work?

[ubtvsig]

How does a TV 3 Way Coax Splitter Work?

Most of you might already know what the cable splitters are, but for those who do not, this blog is for you. Make sure you read the entire content to see what an amazing investment 3 way coax splitter can be with UBTVSIG.com.

Why need the Cable Splitter?

Making the TV available in all the rooms, at times, can make you think about the traditional cable days. The entire household used to get entertained at a single bill price. Well, in case you have been struggling to do the same with the new technology, the cable TV splitter is one answer to all the worries of yours.

Know that it is for sure not easy for all to afford the cable boxes as they are many rooms, and then UBTVSIG offered 3 way coax splitter in that scenario will be the best and the cheapest option, which can be quite useful for you and your usage just like the old times. When the TV went digital, it did bring in more expenses for the cable TV fanatics. Now, you might be thinking that you will still be spending some or other amount of money when you make the purchase of the cable splitter, but before you take your thoughts ahead, just sit down and compare the price of both of them. We are sure that the research will be able to reveal as to why it will be a good choice to invest in the splitter and why it is cheaper than the cable boxes for all the TVs.

Considering the above, it is therefore important that you remain aware of the best 3 way coax splitter.

Choose USE BROADBAND for your 3 Way Coax Splitter Need

Designed for the CATV, indoor and outdoor usage, the USE BROADBAND cable splitter has corrosion-resistant die-cast housing. The product is of excellent quality and has been approved by the CE after the factory QC test. So, if you are looking for the three way convenience (Hex, Slot, and Robertson) with all the mounting screws therein, the 5-1794 MHz bandwidth horizontal splitter is a great choice you can make.

However, with all the complicated data, we do understand that for a common man, it might become difficult to understand the use of the product, and this is why simplifying it all, the below-mentioned pros and cons, will be quite helpful.

Pros and Cons of the Cable Splitter

Pros

Much cheaper than cable TV boxes.

No worries about the extra charges for installations.

Self-installation is possible with the manual offered.

Cons

Signal loss.

Individual channel view isn’t possible.

Watch where the other person in the other room is going.

However, the last con is not even that difficult as the entire family will be able to watch the same movie or a show by sitting in their individual rooms.

Is it right to purchase 3 Way Coax Splitter?

This is one of the most bothering questions. It will bother you continuously until the time you have invested in the right equipment. So, make the decision quite easy for yourself by asking what is actually much more important to you. Is it the cheap cost or the liberty to watch your favorite channel without interruption? In case you wish to watch the desired channel whenever you want, in such case the TV splitter is definitely not the right choice, and purchasing the cable box would be appropriate. But in case you prefer to buy the splitter, the below-mentioned sub-heads will be helpful.

Installation of Coax Cable Splitter

The coaxial cable splitters, they are difficult to install if you are aware of the right technique. To install the cable signal line means that you turn one signal to multiple signals, and these signals they would reach a couple of other TVs in the house apart from the internet modem.

The cable splitters have one important function, and it is the redistribution of information, and it does it quite well.

What to look for?

If the house does have the coax cable that is 50 feet or longer and it runs through varied rooms, do reconsider the cable splitter option as it will cause signal loss at times. So, for overcoming the concerns, a purchase of the amplified splitter would be helpful.

A best practice here is to have a splitter with a similar number of outputs, as there is a requirement for the number of TVs that are to be connected. Like, when there are 3 outputs, 3 Way Coax Splitter would be helpful.

Installation of Wireless Cable Splitter

To avoid running cables and creating mess, wireless cable splitter would be the right choice. It just needs a small amount of wire. Furthermore, it will be a better choice to connect multiple devices. However, there can be expensive in comparison to the coaxial cables.

View Source:- https://medium.com/@ubtvsig/how-does-a-tv-3-way-coax-splitter-work-6946a2d1c791

Read Our One More Blog: TV Boosters Amplifiers Use and Misuse

[ubtvsig]

Best TV Distribution Amplifier

UBTV Sig provides you the Best TV Distribution Amplifier with 2 Satellite IF and 1 Terrestrial TV. Refer to our Infographics to know more.

[ubtvsig]

TV Boosters Amplifiers Use and Misuse

It will not at all be fair for ranting about misuse of the TV boosters amplifiers without offering any facts which can prove about the same. Without it, such rants will just be another load of the uninformed opinion about which there is a lot too much on the Internet available already.

Now it might be a bit technical, but you must actually know that you should never directly cascade the TV boosters amplifiers; boosters come before the loss, and not after the loss; and never put the booster write before the TV unless otherwise, you’re television is 20 + years old or a given booster is the distribution amplifier for giving you many more sockets and even, in that case, it must be in the loft.

To know more, continue reading this blog ahead.

Do that right

Put the amp in the right place at the top. The overall noise figure, it will be much more similar, and you can gain a little bit of carrier to the noise ratio as the amplifier does have a 3dB noise figure instead of TV 6dB. Now, you will be having the 47dB carrier to the noise on the 64dBuV analog channels at the receiver. The TV will be losing some of it as the noise floor, it is just below a single noise floor. However, you will not be any words off the noise-wise which you were if a TV was located in the loft and it was a lot easier for a family to watch now the TV in the living room.

Now note that you definitely lost the capability for handling large interfering signals that mobile phone interference can get 10dB higher right before it is on to the top, whereas now it is totally right on limit TV boosters amplifiers capacity to handle.

Do that wrong

You cannot blame anyone too much. There are some manufacturers who are actually calling the TV boosters amplifiers the setback amplifiers. Also, you by no means need to offer the power within the loft.

The good news is you will now have much more overload capacity, and that will be around 6db instead of zilch. However, there is also bad news you already have lost a 10db carrier to the noise. So you will be losing around 10db signal for the noise on analog. It will not cost any less for doing the same wrong than it will be to do the same right. So, go ahead and do it right.

Suppose the 59dBuV signal is fed through the 20dB loss and the 22dB amplifier. On one end, there will be the TV boosters amplifiers before the loss, and on the other hand, the loss will be before the use of the amp. The increased amount of gain is completely not is able on one end, and in two terms, it looks less bad on the stills than shimmering on moving image. So, make sure to put the amplifier right before the loss.

Compensation for the split loss

At times all that is needed is to feed the aerial in the two sets. Now, just dividing the signal provides almost half the way (with the use of a passive splitter, none of the wirings of aerial will feed in the terminal block, and so there is a need for preserving matching.

Loss is definitely a loss, no matter if it is picked up in a download or by the split of the signal. So, one will get the nice boosters to range called the distribution amplifiers that consist of the amplifier, which is followed by the splitter of either 2, 4, or even more ways. The amplifier gain gets usually matched to a splitter so that the input to the output level remains quite similar.

Now, this can be put right behind the TV as the TV boosters amplifiers, they come before any loss and all one box.

It was said before to keep it in the loft as it is one of the best places for feeding the bedroom TV and main TV with one short download to all, and as for distribution amps, they often have quite a small amount of the output gain that can nearly compensate for around 10m of the CT100. Now, the given loss is quite low. So, do not sweat it out.

Poor TV sensitivity compensation

Looking at the original correct usage for the TV boosters amplifiers, this might not actually apply to the modern sets, with the exception of some of the PC Card TV tunes. So, you're my prefer concentrating on the modern application of compensating for the loss.

On one end, it goes inside the television set (the bad one), and in that, the noise floor remains at 20dBuV. So if the old black and white television set gets picked, then you will we get this bad signal. However, one hasn’t been able to make the purchase of the one that has remained poor for around 15 years. Now, this has the maximum input level of 100dBuV in the considered case.

The original situation boosters got designed for the noisy old valve front ends. The TV boosters amplifiers make things more sensitive to impulse interference. On the modern TV, a noise floor remains similar to a booster. So you will be able to gain no proper advantage from the end of the booster, but that will make you much more sensitive to the impulse interference. So do not try to use it for the purpose unless otherwise you actually are using it before the known loss for correcting for loss.

In case you need any of the best TV boosters amplifiers, UBTVSIG is available out there to offer the best ones. These product types are electronic and have plastic molding together with metal stamping and die casting. It will help you with all of your requirements and will ensure that you receive the right frequency without any loss. So go ahead and make that purchase today without delay.

View Source:- https://medium.com/@ubtvsig/tv-boosters-amplifierstv-boosters-amplifiers-use-and-misuse-e96f55ba9d32

Read Our One More Blog: TV Distribution Amplifier Goals & Purpose- Do you need one?

[ubtvsig]

TV Distribution Amplifier Goals & Purpose- Do you need one?

TV distribution amplifier, the goal and the purpose of it is to increase the received signals strength to the extent that the same is greater than signal losses that are associated with the distribution system of antenna. For ensuring that all the devices are receiving proper signal strength, it is important that the TV distribution amp is located centrally and is related to the distribution line, as the longer the lines will be, the greater the signal loss will be within the system.

There are some of the  TV distribution amplifier  producing companies that seem to have engineered and also started producing the superior-quality of the devices, which can easily offer professional-grade performance and can support both digital and analog broadcast signals. These amplifiers offer either one/two/four/eight-way distribution ports with very low distortion. Apart from it, these amplifiers have the best f-ports, aluminum housing, weather-sealed for the corrosion resistance, and power coating.

While choosing TV distribution amplifier, one must make sure to find the right place for mounting the same outdoor or indoor, safely. However, before this might be considered, they are some of the customers, who still don't know whether or not they need TV distribution amp and how to make the right pick. If you are one such individual, this blog is for you. Keep reading ahead to know more.

Reasons to get TV Distribution Amplifier

Output Ports Total Numbers

The TV distribution amplifier, on today’s date, comes in different options. There are one/two/four/eight-way output ports. All of the output ports offer the same amount of strong signal availability. The actual signal boost gets determined by the output number on an amplifier. It is because the amplifier does have a fixed amount of the game, and with the output signal being divided, every port will have less signal availability. For example, for the two-way amplifier, 50% of the gain of an amplifier will be made available at each of the output ports.

Now the signal might be divided, but the device is definitely quite helpful as it provides more access to signals through ports.

Capability of Return Path

Within the cable telecommunication network, multimedia terminal adaptors for the cable telephony, cable modems, set-top boxes, etc., all need to be easily able to transmit the signals back within the cable network for allowing the two-way communication and for doing the same signals to get sent back within the cable network, and this is called a return path.

The TV distribution amp has the ability for passing the signals within the return path, back to the cable network. It will not have any kind of impact on the performance of distribution amplifiers when the same gets used for TV antennas, as the frequency range isn’t used for the air TV reception.

Power inserter

This is used for baking the feed power to the distribution amplifier with the use of an RF output port so as to make sure that the distribution amplifier can get mounted at the location where power isn't available. In most of the installations, it becomes quite necessary for using the power insert as the amplifier gets mounted near the power outlet. There aren’t performance advantages to using a power inserter as the same is used for allowing the unit to remain remotely powered when TV distribution amp, it isn’t possible to locate the same near the power outlet. With the right choice of TV distribution amp, one can definitely get proper advantages and a better return on money.

TV Distribution Amplifier is all you need for Your Setup Needs

For many of the antenna installations, the pre-amplifier within the antenna might be all that the amplification the setup needs. The best way for determining if you need the distribution amplifier is by measuring the received levels of signal with the field strength meter being used both at first splinter and the input and at every single TV outlet within the home. As this isn’t usually available for the home installations, determining if the amplifier it is needed can become challenging at times. However, do not forget the rule of thumb when you are trying to view the TV stations within different code areas, and it clearly states that you do need the pre-amplifier.

The distribution amplifiers are very easy to be added, and therefore It is recommended that the installation gets done without using the TV distribution amplifier  and then later adding the same if the need is felt after the installation is completed.

Final words

Note that, in case there exist greater than four outlets and the cable length from an antenna to distribution amplifier input, it is either 50 ft or longer, and also the cable length from a given distribution amplifier to the TV set, it is 25 ft or longer, there is a requirement of distribution amplifier. So go ahead and connect with UBTVSIG, the professional manufacturer of television distribution amplifiers. With their experience and understanding to create a lot of benefits for the customers, they ensure high quality, better delivery, and very high customer satisfaction. So, all you need to do is connect and leave the rest to them, as to they are the best in whatever they do.

Connect today for more!

View Source:- https://medium.com/@ubtvsig/tv-distribution-amplifier-goals-purpose-do-you-need-one-ee9f9ef39e99