#RammingMass

[cxrefractories]

Lining method of EAF bottom ramming material

Lining preparation

Clean up the permanent layer residue, dust, iron wire, plastic cloth and other foreign objects. Calculate the knot size, the actual knot thickness is equal to the required knot thickness multiplied by 1.09, and a sufficient amount of ramming material should be prepared according to the construction furnace slope and furnace bottom size requirements. After receiving the material, check whether the ramming material has debris and damp. The debris should be cleaned up. The damp material should not be used, and knotting equipment such as rammers and pneumatic picks should be prepared. Lining method After shoveling the material flat with a shovel, step on it with your feet to remove the air, insert the steel drill into the material and shake it repeatedly, and then use your feet to further solidify. The construction thickness of each layer of ramming material is 150~200mm. Appropriate, and then use a knotting implement to repeatedly beat it 3 times in a spiral from the periphery to the center. The method to check the quality of knotting is usually to put a round steel with a diameter of 5mm on the ramming layer and press it down with a pressure of 10kg, and its depth does not exceed 30mm. Steel drills can be inserted forcefully during site construction, and the depth should not exceed 30mm. The method of knotting the furnace slope is the same as that of the furnace bottom. First, use your feet firmly, and then use the knotting appliance to ram, the maximum angle between the furnace slope and the furnace bottom does not exceed 40°. Prevent rolling or collapse due to the furnace slope is too large. Place bricks at the tapping mouth, furnace door and other places where molten steel is agitated and scour severely should be beaten vigorously and appropriately thickened to extend the service life of refractory materials in these damaged parts as much as possible. After the ramming is finished, cover the 5~10mm thick steel plate on the ramming material to prevent the shape of the furnace bottom being damaged or the waste steel penetrates the ramming material layer when loading the scrap steel, which may cause the hidden danger of steel leakage. If steel cannot be made in time, 100~200mm thick lime is added to the iron plate to prevent the ramming material from hydrating.

We Changxing Refractory Material Co.,LTD is professional manufacturer and supplier of refractory materials for more than 30 years. Our high quality refractory products are good sold to many countries say South Africa, Bangladesh, Indonesia, Malaysia, etc.

Article Source:Lining method of EAF bottom ramming material Company name: Henan Xinmi Changxing Refractory Materials Co.,Ltd Email: info@cxrefractories.com Website:http://www.cxrefractories.com

[cxrefractories]

Reasons and solutions for lining material burst of intermediate frequency furnace

Reason one for the bursting of the lining material of the intermediate frequency furnace:

After the micropowder is introduced into the intermediate frequency furnace, many small gaps are filled, which reduces the air permeability of the intermediate frequency furnace lining material and causes bursting.

Reason two for the explosion of the lining material of the intermediate frequency furnace:

The zeolite-like calcium-aluminum-silicon hydrate or gel formed in the lining of traditional intermediate frequency furnaces rarely forms exhaust passages due to the decomposition of hydrates before 300 degrees. After 300 degrees, the rapid dehydration releases a large amount of water vapor and causes bursting.

The easy solution to the bursting of the

lining material of the intermediate frequency furnace

:

1. Use a reasonable drying and heating system to control the maximum vapor pressure inside the furnace lining;

2. Add explosion-proof materials such as explosion-proof agent to the furnace lining to increase the air permeability of the hardened body and reduce the internal vapor pressure of the castable.

We Changxing Refractory Material Co.,LTD is professional manufacturer and supplier of refractory materials for more than 30 years. Our high quality silica ramming mass are good sold to many countries say South Africa, Bangladesh, Indonesia, Malaysia, etc. Shall any interests, welcome to contact us. Our team would make best to be your reliable partner!

Article Source:Causes of perforation of ladle nozzle in use and solutions Company name: Henan Changxing Refractory Materials Co.,Ltd More refractory products:https://www.cxrefractories.com/en-product-solution Email:info@cxrefractories.com Website:https://www.cxrefractories.com