#MCUD1

[hongtelecom-blog]

MA5600T MA5603T MA5608T xPON Board Function Compared

MA5600T MA5603T MA5608T xPON Board Function Compared

MA5600T MA5603T(SCUN / SCUK + PRTE)

MA5608T(MCUD+MPWC) GE uplink, DC power (MCUD1+MPWD) 10G uplink, AC power

  MA5600T MA5603T MA5608T xPON Board Function Compared

H801GPMD Board H801GPMD is an 8-port GPON OLT Interface Board, which works with the CMC to provide GPON access service in the MSO scenario.

H801GPMD Board

  H802GPFD Board H802GPFD is a 16-port GPON OLT Interface Board, which works with…

[rodrigocarran]

Instalando MCUD1 no Huawei MA5608

Instalando MCUD1 no Huawei MA5608

Uma vez em um GPON OLT Huawei MA5608 e uma placa MCUD normal, quando o tráfego da Internet começou a atingir 900 Mb / s, foi necessário substituir o MCUD por MCUD1 com portas de 10 Gb / s.

Noto imediatamente que no MCUD1 as portas 0 e 1 têm 1 Gb / s, as portas 2 e 3 têm 10 Gb / s.

Primeiro, olhei quais placas estão instaladas:

1 2 3 4 5 6 7 8 9 10 11 MA5608T(config)#display board 0 ----…

[thunderlinkcom]

The MAC Address Table Configuration of display mac-address(distributing-mode)

Function Description

To meet the requirements of bearing multiple services, the MA5680T/MA5683T/MA5608T supports the MAC address table and the MAC address pool. The MAC address table of the MA5680T/MA5683T/MA5608T is capable of learning new MAC addresses. If the source MAC address of a received packet does not exist in the table, the MA5680T/MA5683T/MA5608T can add the source MAC address and the port number of the received packet to the table as a new item. Dynamic MAC addresses in the MAC address table also have the aging function. The MA5680T/http://www.thunder-link.com/HUAWEI-MA5683T_p580.htmlT/MA5608T deletes the associated address items of a device that has not sent any packet for a certain period.

display mac-address(distributing-mode)

Function

This command is used to query the information about the MAC address table in the system. To query the dynamic and static MAC addresses in the MAC address table after a MAC address is added to or deleted from the MAC address table, run this command.

Format

display mac-address board frameid/slotid

display mac-address port frameid/slotid/portid [ont ontid ]

display mac-address vlan vlanid

display mac-address all

display mac-address static

display mac-address meth

display mac-address service-port index

display mac-address config

display mac-address { vsi vsi-name [ ac [ vlan vlanid ] ] | pwindex pwindex }

Parameters

Parameter

Description

Value

board frameid/slotid

Indicates the subrack ID and slot ID. Enter a slash (/) between the subrack and slot IDs. To query the MAC addresses of a specific board, use this parameter.

Please see Differences Between Shelves.

port frameid/slotid/portid

Indicates the subrack ID, slot ID, and port ID. Enter a slash (/) between the subrack, slot, and port IDs. To query the MAC address of a specific port, use this parameter.

Please see Differences Between Shelves.

vlan vlanid

Indicates the VLAN ID. It uniquely identifies a VLAN. To query the MAC address of a specific VLAN, use this parameter.

Numeral type. Range: 1-4093.

AC VLAN range: 2-4093.

static

Queries the static MAC address. To query all the static MAC addresses in the MAC address table, use this parameter.

-

all

Queries all MAC addresses in the MAC address table.

-

meth

Indicates the MAC address of the METH port.

-

service-port index

Indicates the ID of the service port. when querying the MAC address of a specified service port in the MAC address list, use this parameter.

Numeral type,Range:

SCUK/SCUL/SCUN:0-32767.

SCUB/SCUF:0-16383.

SCUH/SCUV:0-131071.

MCUD/MCUD1/MCUE:0-20479.

config

Query the configuration of MAC addresses.

-

vsi vsi-name

Indicates the VSI name. It uniquely identifies a VSI.

Character string type, a string of 1-15 characters. Only numbers, letters (case sensitive), and underline (_) are allowed.

pwindex pwindex

Identifies a PW uniquely in the system.

Numeral type. Range: 1-2944.

ac

Identifies theattachment circuit. The attachment circuit is the connection between a CE and a PE. It can be a physical port or a virtual port.

Currently, only the mapping from a VLAN to an AC is supported.

-

ont ontid

Identifies theONT ID.

Numeral type. Range: varies with the board type.

Modes

Privilege mode

Level

Operator level

Usage Guidelines

For the filtering function provided by this command, the result is displayed in rows.

Example

To query the MAC address of the ADSL port 0/3/0, do as follows:

huawei#display mac-address port 0/3/0  -----------------------------------------------------------------------   SRV-P BUNDLE TYPE MAC            MAC TYPE F /S /P   VPI  VCI   VLAN ID   INDEX INDEX  -----------------------------------------------------------------------       0     -  adl  00e0-fc00-1000 static   0 /3 /0   0    35        100  -----------------------------------------------------------------------  Total: 1  Note: F--Frame, S--Slot, P--Port, F/S/P indicates PW Index for PW,        A--The MAC address is learned or configured on the aggregation port        VPI indicates GEM Port ID for GPON,        v/e--vlan/encap, pri-tag--priority-tagged,        ppp--pppoe, ip--ipoe, ip4--ipv4oe, ip6--ipv6oe

To query all the MAC addresses that belong to VLAN 10 in the MAC address table, do as follows:

huawei#display mac-address vlan 100  It will take some time, please wait...  -----------------------------------------------------------------------   SRV-P BUNDLE TYPE MAC            MAC TYPE F /S /P   VPI  VCI   VLAN ID   INDEX INDEX  -----------------------------------------------------------------------       0     -  adl  00e0-fc00-0002 static   0 /3 /0   0    35        100  -----------------------------------------------------------------------  Total: 1  Note: F--Frame, S--Slot, P--Port, F/S/P indicates PW Index for PW,        A--The MAC address is learned or configured on the aggregation port        VPI indicates GEM Port ID for GPON,        v/e--vlan/encap, pri-tag--priority-tagged,        ppp--pppoe, ip--ipoe, ip4--ipv4oe, ip6--ipv6oe

To query all the MAC addresses that belong to PW index 1 in the MAC address table, do as follows:

huawei#display mac-address pwindex 1  ---------------------------------------------------------------------  SRV-P BUNDLE TYPE MAC            MAC TYPE F /S /P  VPI  VCI   VLAN ID  INDEX INDEX  ---------------------------------------------------------------------      -    -   pw   00e0-fc00-0101 static   1        -    -         100      -    -   pw   00e0-fc00-0102 static   1        -    -         100      -    -   pw   00e0-fc00-ff01 dynamic  1        -    -         100  ---------------------------------------------------------------------  Total: 3  Note: F--Frame, S--Slot, P--Port, F/S/P indicates PW Index for PW,        A--The MAC address is learned or configured on the aggregation port        VPI indicates GEM Port ID for GPON,        v/e--vlan/encap, pri-tag--priority-tagged,        ppp--pppoe, ip--ipoe, ip4--ipv4oe, ip6--ipv6oe

System Response

The system displays the queried result when the command runs successfully.

The following table describes the parameters in response to the display mac-address command. In the case of an xDSL port, it is the virtual path identification. In the case of a GPON port or a EPON port, it is the ONT ID. In the case of an xDSL port, it is the virtual channel identification. In the case of a GPON port, it is the GEM port ID. In the case of an EPON port, it is meaningless.

Parameter

Description

SRV-P INDEX

Indicates the ID of the service port.

BUNDLE INDEX

Indicates the bundle ID of the service port.

Type

Indicates the type of the service port with the MAC address. Options: atm, eth, adl, vdl, shl, pw, and ac.

MAC

MAC address.

MAC Type

Indicates the MAC address type. Options: static, dynamic and anti-spf.

F /S /P

Indicates the subrack ID, slot ID, and port ID of the service port with the MAC address.

VPI

VCI

VLANID

Indicates the VLAN of the service port with the MAC address.

[hongtelecom-blog]

Huawei OLT Hot spot GPON XGPON Board introduction

Huawei OLT Hot spot GPON XGPON Board introduction

MA5600T (SCUN / SCUK + PRTE)

MA5603T (SCUN / SCUK + PRTE)

MA5680T (SCUN / SCUK + PRTE)

MA5683T (SCUN / SCUK + PRTE)

MA5608T(MCUD+MPWC) GE uplink, DC power

MA5608T(MCUD1+MPWD) 10G uplink, AC power

MA5606T (MCUA + MPWA)

  Hot spot GPON XGPON Board

GPFD Board (C+/C++/B+)

H802GPFD is a 16-port GPON OLT Interface Board, which works with the ONU to provide GPON access service. External Interfaces

The…

[hongtelecom-blog]

Huawei OLT MA5606T and MA5608T Basic configuration Function Compared

Huawei OLT MA5606T and MA5608T Basic configuration Function Compared

MA5606T and MA5608T Basic configuration Function

Physical Specifications  MA5608T

This topic provides the dimensions, weight, and power consumption of the MA5608T chassis.

Dimensions and Weight Dimensions and weight of the MA5608TItem Specification Dimensions (W x D x H, excluding mounting brackets) 442mm×244.5mm×88.1mm Dimensions (W x D x H, including mounting brackets of IEC…

[hongtelecom-blog]

MA5608T Basic configuration Board introduction OLT Huawei

MA5608T Basic configuration Board introduction OLT Huawei

Appearance

The MA5608T has a fan tray at the left. The subrack is installed in the cabinet through the mounting brackets.

MA5608T chassis(xDSL) 

Appearance of the MA5608T chassis(xDSL)

Appearance of the MA5608T chassis(GPON)  MA5608T chassis(GPON) 

  Physical Specifications

This topic provides the dimensions, weight, and power consumption of the MA5608T chassis.

Dimensions and Weight Tab…

[hongtelecom-blog]

Huawei MA5608T OLT

Appearance The MA5608T is 2 U high.

Figure 1 Appearance of the MA5608T chassis(xDSL)

Figure 2 Appearance of the MA5608T chassis(GPON)

Specification

This topic provides the dimensions, weight, and power consumption of the MA5608T chassis.

Dimensions and weight of the MA5608T Item Specification Dimensions (W x D x H, excluding mounting brackets) 442mm×244.5mm×88.1mm Dimensions (W x D x H,…

[rodrigocarran]

Instalando MCUD1 no Huawei MA5608

Instalando MCUD1 no Huawei MA5608

Uma vez em um GPON OLT Huawei MA5608 e uma placa MCUD normal, quando o tráfego da Internet começou a atingir 900 Mb / s, foi necessário substituir o MCUD por MCUD1 com portas de 10 Gb / s.

Noto imediatamente que no MCUD1 as portas 0 e 1 têm 1 Gb / s, as portas 2 e 3 têm 10 Gb / s.

Primeiro, olhei quais placas estão instaladas:

1 2 3 4 5 6 7 8 9 10 11 MA5608T(config)#display board 0 -----…

[thunderlinkcom]

What’s the xDSL Bonding Group Profile Configuration of display xdsl bonding-group-profile

This topic describes the commands related to xDSL bonding group profile configuration in TR165 mode. The commands can be used to add, delete, modify, and query an xDSL bonding group profile.

display xdsl bonding-group-profile

Function

This command is used to query the information about a bonding group profile. To query information about a configured bonding group profile, run this command.

Format

display xdsl bonding-group-profile [ profile-index ]

Parameters

Parameter

Description

Value

profile-index

Indicates the index of a bonding group profile. When you specify a profile index, the system displays the detailed information about the profile.

Numeral type. Range:

SCU board: 1-256

MCUD/MCUD1: 1-48

Modes

Global config mode

Level

Operator level

Usage Guidelines

When querying the detailed information about a bonding group profile, you can specify the profile index to query the information about the specified profile or query the information about all bonding group profiles in the system without specifying the profile index.

Example

To query the detailed information about the bonding group profile with index of 2, do as follows:

huawei(config)#display xdsl bonding-group-profile { <cr>|profile-index<U><1,256> }:2  Command:           display xdsl bonding-group-profile 2  ------------------------------------------------------------------------------  Profile index                              : 2  Profile name                               : GROUP PROFILE 2  Maximum interleaving delay downstream(ms)  : 3  Maximum interleaving delay upstream(ms)    : 3  Minimum impulse noise protection downstream: 0.5 Symbol  Minimum impulse noise protection upstream  : 0.5 Symbol  Minimum transmit rate downstream(Kbps)     : 0  Maximum transmit rate downstream(Kbps)     : 0  Target transmit rate downstream(Kbps)      : 0  The downstream data rate threshold(Kbps)   : 0  Minimum transmit rate upstream(Kbps)       : 0  Maximum transmit rate upstream(Kbps)       : 0  Target transmit rate upstream(Kbps)        : 0  The upstream data rate threshold(Kbps)     : 0  The data rate threshold switch             : Disable  The bonding CPE incorrect alarm switch     : Disable  ------------------------------------------------------------------------------

To query information about all bonding group profiles configured in the system, do as follows:

huawei(config)#display xdsl bonding-group-profile { <cr>|profile-index<U><1,256> }: Command:           display xdsl bonding-group-profile ------------------------------------------------------------------------ Profile Index     Profile Name ------------------------------------------------------------------------             1     DEFVAL             2     GROUP PROFILE 2             3     GROUP PROFILE 3             4     hw ------------------------------------------------------------------------ Total: 4

System Response

The system displays the queried result when the command runs successfully.

The following table describes the parameters in response to the display xdsl bonding-group-profile 2 command.

The following table describes the parameters in response to the display xdsl bonding-group-profile command.

Parameter

Description

Profile index

Indicates the bonding group profile index.

Profile name

Indicates the bonding group profile name.

Maximum interleaving delay downstream

Indicates the downstream maximum interleave delay. The interleave delay refers to the delay that results from the interleave processing of a bit stream. It is related to the interleave depth, the symbol length, and the line rate.

Maximum interleaving delay upstream

Indicates the upstream maximum interleave delay. The interleave delay refers to the delay that results from the interleave processing of a bit stream. It is related to the interleave depth, the symbol length, and the line rate.

Minimum impulse noise protection downstream

Indicates the downstream minimum impulse noise protection (INP). The INP defines how many consecutive discrete multi-tone (DMT) symbols can be protected, that is, how many consecutive error DMT symbols in a certain number of bytes can be corrected in the de-interleaving process. The upstream and the downstream parameters are configured separately. The following symbol lengths are available: no protection, 0.5 symbol, 1 symbol, 2 symbols, ..., 16 symbols.

Minimum impulse noise protection upstream

Indicates the upstream minimum INP. The INP defines how many consecutive DMT symbols can be protected, that is, how many consecutive error DMT symbols in a certain number of bytes can be corrected in the de-interleaving process. The upstream and the downstream parameters are configured separately. The following symbol lengths are available: no protection, 0.5 symbol, 1 symbol, 2 symbols, ..., 16 symbols.

Minimum transmit rate downstream

Indicates the downstream minimum transmission rate. When this parameter is set to 0, the transmission rate is not limited.

Maximum transmit rate downstream

Indicates the downstream maximum transmission rate. When this parameter is set to 0, the transmission rate is not limited.

Target transmit rate downstream

Indicates the target downstream transmission rate. Generally, the sum of rates does not exceed the target upstream rate. If the sum of rates exceeds the target upstream rate, reduce the transmit power of the members, or decrease the rates of the members by increasing the signal to noise ratio (SNR) margin. This is to ensure that requirement of the target rate can be met. When the target rate is set to 0, the sum of the rates for all members in a group is not limited.

The downstream data rate threshold

Indicates the downstream rate monitoring threshold.

Minimum transmit rate upstream

Indicates the upstream minimum transmission rate. When this parameter is set to 0, the transmission rate is not limited.

Maximum transmit rate upstream

Indicates the upstream maximum transmission rate. When this parameter is set to 0, the transmission rate is not limited.

Target transmit rate upstream

Indicates the target upstream transmission rate. Generally, the sum of rates does not exceed the target upstream transmission rate. If the sum of rates exceeds the target upstream rate, reduce the transmit power of the members, or decrease the rates of the members by increasing the SNR margin. This is to ensure that requirement of the target rate can be met. When the target rate is set to 0, the sum of the rates for all members in a group is not limited.

The upstream data rate threshold

Indicates the upstream rate monitoring threshold.

The data rate threshold switch

Indicates the rate threshold alarm function.

The bonding CPE incorrect alarm switch

Indicates the switch for reporting the alarm indicating the incorrect peer CPE in the bonding group.

Parameter

Description

Profile index

Indicates the bonding group profile index.

Profile name

Indicates the bonding group profile name.