#3.2v 280ah lithium ion batteries

[neexgent]

Neexgent Brand New 280ah Lithium Ion Lifepo Battery Cell Catl Grade A 3.2v Lifepo4 Battery

Neexgent 3.2v 280ah lifepo4 cell Lithium Ion Batteries solar batteries Genuine Grade A lifepo4 battery cell

[qhtechnology]

Build A 12V 280Ah LiFePO4 For A Golf Cart! Full Process Of Battery Cell Assembly！

LiFePO4 batteries have lots of advantages and are becoming quite in demand in the market of trolling motors. When referring to the LiFePO4 batteries, you may compare them with the GEL batteries. For a long time, GEL batteries have played a role in our lives. Nowadays, we prefer LiFePO4 batteries.

As opposed to boats that use GEL batteries, electrical ships equipped with the 12.8Volt 280Ah lithium batteries are more economical, less polluting, and clearly better for the environment. The LiFePO4 battery has a longer life span and deep cycle times(even more than 5,000 times).

Are you a Lithium battery amateur and interested in li-ion battery pack assembly? Now we’d like to share the whole assembly process for beginners, which takes the 12.8V 280Ah LiFePO4 battery as an example.

*Note: It is recommended that you learn some basic knowledge about LiFePO4 batteries before assembling the battery pack. Keep safe when you are assembling the battery pack.

Material Used

3.2V 280Ah LiFePO4 battery cells (4 pieces)

There are currently three common shapes of LiFePO4 batteries: cylindrical, prismatic, and pouch. Different shapes of batteries will have a certain impact on performance. At present, the most suitable battery DIY enthusiasts are the prismatic LiFePO4 batteries, which are very suitable for both performance and operational difficulty. 

We recommend you purchase the Grade A battery with a high quality and reliable warranty.

BMS (Battery Manage System, 1 piece)

Connectors (About 4pieces)

Others: EVA cotton, screws, ribbon cable, plastic pipes, etc.

Tool Used:

Spot Welder

Spot Welding Pen

Soldering Iron

Wire Cutter

Wire Stripper

Multimeter

Assembly Methods: 4 Series And 1 Parallel

Series(S): The way of connecting the positive and negative electrodes of two different cells is called a series connection. As a result, the voltage of the battery pack will increase while the capacity remains the same.

Parallel(P): where the positive and positive electrodes of two different cells are connected in parallel. The result is that the capacity of the battery pack increases while the voltage remains the same.

Assembly Process

1. Install Signal Acquisition Wires In Sequence

The connecting piece has been connected to the battery cell by laser welding. Before installing the signal acquisition, we checked the consistency of the battery and fixed them with fiber tape.

2. Cut The Signal Lines To An Appropriate Length

Tidy up the signal lines and tape them with fiber tape, then cut the signal lines to an appropriate length.

3. Soldering Signal Lines With Lead-Free Solder

Generally, leaded solder is composed of tin and lead. The advantages of using leaded solder include: being easier to bring to working temperature, being shock resistant, and having fewer internal flaws in the structure after being cooled. However, lead material is harmful to the body as it’s readily absorbed. We’d better choose lead-free solder to protect our health and environment.

4. Connect The Positive And Negative Power Line With Connecting Pieces

5. Connect The Power Line

6. Connect The B- Of BMS To The Negative Of Battery Pack

A BMS is one of the most important elements in a LiFePO4 battery, like the brain of the battery pack. It calculates the State of Charge (the amount of energy remaining in the battery) by tracking how much energy goes in and out of the battery pack and by monitoring cell voltages, which can prevent the battery pack from overcharging, over-discharging, and balancing all the cells voltage equally.

There are two main sets of wires we need to install, the thick wires and the thin wires. The thick wires are your charging/discharging wires and the thin wires are your balance wires. Not every BMS is the same, but most are similar. Your BMS will likely have 3 thick wires or 3 pads to solder on your own heavy gauge wires. These are the B-, P-, and C- wires (or pads for adding wires). We usually start with the B- wire. We can connect the B- of BMS to the negative pole of the battery pack.

7. Put The Battery Pack Into Shell, And Fill The EVA Cotton

EVA cotton can be shockproof, fireproof, and insulated.

8. Secure BMS With Thermally Conductive Tape

The thermally conductive tape for battery packs keeps the BMS in place and protects them from the shock of extreme temperature changes. 

Besides, these tapes provide electrical insulation, which prevents short circuits and provides a barrier to BMS.

9. Check The Signal Lines In Correct Order

Pay attention, the wrong sequence may cause BMS to burn out!

10. Install Positive And Negative Power Lines To The Cap

11. Plug Signal Acquisition Wires’ Port Into Interface

12. Fill EVA Cotton

EVA cotton can be shockproof, fireproof, and insulated.

Battery Tests

13. Test Voltage Of The Battery Pack

In these steps, we can use a multimeter to check the voltage of the whole battery pack. Attach the multimeter probes to the positive and negative battery terminals. Then we can check the voltage on the screen. The multimeter’s red probe must be connected to the positive terminal, while the black probe must be connected to the negative one.

A fully-charged battery must indicate a slightly higher voltage than the voltage listed on the battery. For instance, a 12 volts battery will indicate about 12.8 volts when it is fully charged.

14. Charging Test

The battery capacity, or the amount of energy a battery can hold, can be measured with a battery analyzer. If you’re doing a capacity test, be sure to charge the battery until the battery reaches 100%. Then discharge the device until the battery is fully depleted. The charge and discharge rates of a battery are governed by C rates. The capacity of a battery is commonly rated at 1C, meaning that a fully charged battery rated at 280Ah should provide 280A for one hour.

15. Discharging Test

The discharging test of the battery is very helpful to the battery cycle life and discharge performance evaluation. We can use a professional device(Such as a Programmable DC Electronic Load) to check whether the battery works well or not during the discharging process, which can protect our battery and devices for further daily using.

When testing, there are three factors we need to pay attention to the port voltage of the battery, the resistance of the wire between the battery and the electronic load, and the temperature of the battery.

Summary

After assembling and testing the batteries step by step successfully, you will get your new 12.8V 280Ah LiFePO4 battery pack! It is suitable for your golf cart or other applications(such as household solar energy storage, Recreational Vehicle, Yacht, etc.)

Thanks for reading the full tutorial on assembling the 12.8V 280Ah LiFePO4 battery! It is not hard for us to build a LiFePO4 battery. Which voltage and capacity of the LiFePO4 battery do you need?

[neexgent]

Neexgent Lifepo4 Battery Cell 4 Pieces Lifepo4 3.2v 280ah Lithium Ion Batteries Lifepo4 Battery Pack

[neexgent]

Neexgent Prismatic Lithium Iron Phosphate Battery Lifepo4 Battery Cell 3.2v 280ah Lifepo4 Cell

Neexgent 3.2V 280Ah Li-ion Lithium Rechargeable Battery LiFePO4 Cell for Electric Car Bus EV

[neexgent]

Neexgent Wholesale 3.2V 280ah Grade A Brand New Solar Energy Prismatic Cell Lithium Lifepo4 3.2 Battery

Neexgent Grade A Deep Cycle Battery Over 6000 Times 280Ah Lithium Ion Phosphate Prismatic Lifepo4 Battery Cells 3.2v

[neexgent]

Neexgent Grade A brand Lifepo4 Phosphate Prismatic Lithium Ion 3.2V Battery Cells 280AH Battery Pack

Neexgent Rechargeable 4PCS Grade A 280Ah Lifepo4 Cells 3.2V Lifepo4 280Ah Battery Cell is the perfect choice for you.