#2016centerconsole

[agearhead4life]

Pic 9 & final on the console. It's all bolted in and fits well. I figured since I've already got the seats out, I'll remove the rubber matt and wet padding underneath it to put down some FatMat (like Dynomat), new padding and the carpet from the short bed donor truck. Today I'm finally adapting the newer 2016 Tahoe center console to actually bolt down in the Vandal. It's been just sitting in the truck squeezed between the seats. I'll cut the old base bracket and weld it to the new console so that it bolts in like the Vandal's original middle seat did. #vandalproject #nbsconsole #nbscenterconsole #tahoeconsole #2016centerconsole

[agearhead4life]

Pic 8 The side and front plastic trim snapped back on with no issues. The rear piece had to be trimmed a little to clean the trans tunnel. Today I'm finally adapting the newer 2016 Tahoe center console to actually bolt down in the Vandal. It's been just sitting in the truck squeezed between the seats. I'll cut the old base bracket and weld it to the new console so that it bolts in like the Vandal's original middle seat did. #vandalproject #nbsconsole #nbscenterconsole #tahoeconsole #2016centerconsole

[agearhead4life]

Pic 7 Mounted! Now to snap the plastic trim back on. The rear piece will have to be trimmed a little. Today I'm finally adapting the newer 2016 Tahoe center console to actually bolt down in the Vandal. It's been just sitting in the truck squeezed between the seats. I'll cut the old base bracket and weld it to the new console so that it bolts in like the Vandal's original middle seat did. #vandalproject #nbsconsole #nbscenterconsole #tahoeconsole #2016centerconsole

[agearhead4life]

Pic 6 The mounts are now trimmed, welded and painted. Today I'm finally adapting the newer 2016 Tahoe center console to actually bolt down in the Vandal. It's been just sitting in the truck squeezed between the seats. I'll cut the old base bracket and weld it to the new console so that it bolts in like the Vandal's original middle seat did. #vandalproject #nbsconsole #nbscenterconsole #tahoeconsole #2016centerconsole

[agearhead4life]

Pic 5 Now the 2016 Tahoe console is set on top of the old mounting brackets to see what to trim and set the seat angle before welding the old base to the new console. I angled it back slightly so that the person sitting there will be comfortable. Today I'm finally adapting the newer 2016 Tahoe center console to actually bolt down in the Vandal. It's been just sitting in the truck squeezed between the seats. I'll cut the old base bracket and weld it to the new console so that it bolts in like the Vandal's original middle seat did. #vandalproject #nbsconsole #nbscenterconsole #tahoeconsole #2016centerconsole

[agearhead4life]

Pic 4 This is the old 2001 middle seat mounting brackets that I cut off and bolted into their place on the floor. Now to set the 2016 Tahoe console on top of them to see what to trim before welding the old base to the new console. Today I'm finally adapting the newer 2016 Tahoe center console to actually bolt down in the Vandal. It's been just sitting in the truck squeezed between the seats. I'll cut the old base bracket and weld it to the new console so that it bolts in like the Vandal's original middle seat did. #vandalproject #nbsconsole #nbscenterconsole #tahoeconsole #2016centerconsole

[agearhead4life]

Pic 3 This is the old 2001 middle seat base from the Vandal after cutting the mounts off to use on the 2016 Tahoe console. Today I'm finally adapting the newer 2016 Tahoe center console to actually bolt down in the Vandal. It's been just sitting in the truck squeezed between the seats. I'll cut the old base bracket and weld it to the new console so that it bolts in like the Vandal's original middle seat did. #vandalproject #nbsconsole #nbscenterconsole #tahoeconsole #2016centerconsole

[agearhead4life]

Pic 2 Today I'm finally adapting the newer 2016 Tahoe center console to actually bolt down in the Vandal. It's been just sitting in the truck squeezed between the seats. I'll cut the old base bracket and weld it to the new console so that it bolts in like the Vandal's original middle seat did. #vandalproject #nbsconsole #nbscenterconsole #tahoeconsole #2016centerconsole