sinogomine

[sinogomine]

What's the matter with the finished product of the ball briquette machine?

The briquette machine equipment can obtain high-quality and environmentally friendly new briquette products by pressing raw materials such as coal powder, coal slime, and cinders. The size of the briquette pellets produced by the briquette machine equipment can be determined and changed in combustion characteristics, and the properties are stable. , which is superior to natural lump coal. At the same time, the porosity of processed briquette pellets is significantly larger than that of natural lump coal, and the gas permeability is better during combustion, so the combustion efficiency is higher. According to the needs of combustion and environmental protection, Adding sulfur-fixing agent and other auxiliary materials in the pressing production of the ball press, not only the combustion performance is improved compared with the raw coal after the pressing, but the smoke and dust emission is also significantly reduced, achieving the effect of environmental protection.

Users who buy the ball briquette machine know that its core part is the forming roller. Today, let’s analyze the phenomenon that the finished product of the ball press machine is not easy to demould:

1. The moisture of the raw material pressed by the ball briquette machine does not reach the standard, and the humidity is too high, which will easily cause material blockage and difficult demoulding. Solution: Control the moisture content to between 8% and 13%. Natural drying or mechanical drying can be used.

2. Does the material enter the ball press machine evenly? If the material is not evenly fed, of course it is not easy to demould. The solution is to use an automatic feeder to feed evenly.

3. The ball socket of the ball pressing machine is too small. The size of the ball socket of the ball pressing machine is also related to the ball output rate of the ball pressing machine. If the ball socket is too small, it is not easy to demould. The solution is that the ball socket is larger than 3 cm.

4. The speed of the ball pressing machine should not be too low. The speed of the ball pressing machine should be between 10-20 revolutions.

5. The quality of the forming roller of the briquette machine is also very important. It is the core part of the entire machine and the premise to ensure smooth briquette production.

When choosing ball press equipment, users should start from their own working performance, aim at solving actual needs, choose the best, and choose the right manufacturer to choose the right price.

If you want to know about more briquette machine informations, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

What are the factors that affect the price of the coal briquette machine production line?

With the vigorous development of my country's coal mining industry, while producing a large amount of high-calorie coal, many pulverized coal and coke with low ignition point and low calorie have also been derived. The value of these coals is low, so it is particularly important to reprocess them with economic value, and coal briquette equipment has emerged as the times require. The coal briquette equipment has the characteristics of small footprint, low investment, and quick returns, which are sought after by many customers, but now the price of the same type of briquette production line on the market varies greatly. What is the reason for this? Today, the editor will explain to you what are the factors that affect the price of the coal briquette machine production line

  1. Ball pressing machine:

The briquette machine production line is a complete production line, not a single piece of equipment. The most important thing in the briquette production line is the briquette machine that plays the role of forming. A briquette machine with high ball forming rate, reasonable design and durability often determines whether the briquette production line can complete the production work normally. . The price of the briquette machine also determines the overall price of the briquette equipment. If the price of the briquette machine is high, the price of the briquette production line will naturally be higher.

Second, supporting equipment:

The price in the production line will also be affected by other supporting equipment. The conventional supporting equipment of the briquette production line includes crushers, batching machines, mixers, conveyor belts and dryers. The batching machine is responsible for feeding different raw materials into the mixer according to the ratio. , fully stirred, and can participate in molding after stirring. After forming, it is sent to drying by the conveyor belt, and after drying, it becomes our finished briquettes. Of course, compared with the ball pressing machine, these are optional equipment. In order to save investment costs in the early stage, some customers may select a part of them for production, and replace the other parts manually, and then install them after generating economic benefits in the later stage, which also leads to fluctuations in the price of briquette production lines.

Three, manufacturer strength:

After talking about the equipment, we have to talk about the factors of the manufacturer. Strong manufacturers, guaranteed equipment quality, reasonable equipment prices, and good service in all phases, these are often unmatched by workshop-type manufacturers, and naturally the prices cannot be compared.

If you want to know about more briquette machine, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

How to choose coal briquette machine?

The briquette machine is a device for pressing powder materials into balls. The ball pressing device is widely used. It can press the following materials, granulate or press balls, such as aluminum chips, activated carbon, alumina, bauxite, etc. It is a kind of equipment used to crush powder materials. Ball briquette equipment is widely used, and it can be pressed into the following materials: aluminum chips, activated carbon, alumina, bauxite, caustic soda, charcoal, clay, coke chips, etc. The goal is to reduce dust, control bulk density, recycle, improve transport performance, etc.

The use of briquette briquette machine greatly increases the utilization rate of pulverized coal. The production technology of coal briquette forming machine started and developed relatively late in our country, but this does not affect the further development and wider application of briquette briquette machine. Moreover, according to our country's economic situation and the idea of environmental protection, the development of our country's briquette briquette machine will be very good and has a very good market potential. We all know that there are many specifications of briquette briquette machines, which makes it difficult for users to choose, so how to choose briquette briquette machines? Let me introduce the selection method of the pressure ball machine for you

1. Look at the diameter of the briquette machine

There is a saying that the larger the diameter of the briquette briquette machine, the higher the output. This statement is correct to a certain extent, but it is not inevitable, because the process requirements for a certain material are different. The selection of the machine is also different, and sometimes the processing capacity of the ball press machine with a small diameter may not be small.

2. Look at the line pressure ratio of the briquette machine

  For the line pressure ratio of the briquette machine, it is the experimental result to obtain a certain process purpose. The line pressure ratio is not higher and higher, it must be reasonable, and only reasonable is better.

3. Understand density

  Regarding the density of a single briquette machine, one case is that the briquette briquette machine presses the ball with a certain line ratio, and the other case is a certain density value that the process hopes to achieve, such as high-purity magnesia, and the user may need to obtain a higher density type ball.

4. Look at the processing capacity

The processing capacity depends not on the material throughput at the entrance of the briquette briquette machine, but on the output capacity of qualified briquettes. Different briquette machines have different ball forming rates for the same material.

5. Look at the size of the ball

Different ball types of the same material have different output under the premise of the same pressure roller area, that is, when a certain processing capacity is given, the specifications and models that need to be selected for different ball types are also different.

If you want to know about more briquette machine informations, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

What kinds of adhesives are added to the briquette machine?

The briquette machine is the main machine required for ball pressing, ball making, and ball making processing. It is a device for pressing materials into balls. Before processing, the materials, water, adhesives and other materials are fully stirred, and the addition of adhesives is to increase the finished product. The strength of the ball, waterproof strength, etc., so the configuration and use of adhesives are crucial to the product effect of the entire briquette production line.

1. The physical adhesive of the briquette machine has a non-toxic surface and has a good fixing effect on water molecules. There is a three-layer arrangement of water molecules on the surface, and the water molecules close to the surface are arranged in an orderly manner, such as bentonite, syrup, modified starch and modified cellulose. The hydroxyl group (-OH) contained in these substances has a strong fixing effect on water molecules, and can make water molecules stick together in the initial stage of ball solidification.

2. "Chemical combination" of the briquette machine means that the binder relies on chemical reactions to generate new phases during the combination process, such as ordinary cement, water glass and carbonation consolidation chemical combination. Carbonization curing also belongs to chemical curing. During the consolidation process of some organic binders, under the influence of changing conditions, the molecules undergo polymerization or polycondensation, thereby bonding together more tightly, which is also called chemical bonding.

3. The organic binder of the briquette machine is a synthetic high polymer or mixture, and the viscosity increases rapidly after dissolving. The classic organic binders include sodium carboxymethylcellulose, modified starch series, polyacrylamide, etc. The organic bonding effect is obvious, the mixing ratio is low, the impact on the ball grade is small, and the amount of impurities brought in is small. In addition, the agent burns and disappears after entering the furnace, which can effectively improve the pellet grade and porosity, and is beneficial to the improvement of reducibility and steelmaking index. The modified starch type organic binder type is determined.

If you want to know about more briquette machine, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

How a peat briquette machine ensures smooth balls?

The peat briquette machine can briquette peat, loess, coal slime, molded carbon, sludge, lime powder, fluorite powder and other powdery materials into balls at one time. , gearbox, motor and scrap output, etc., using metal raw materials to ensure the performance and quality of the machine, the mold can be customized or replaced according to customer needs, the ball forming rate is 99%, the finished product has high strength, is not easy to break, and is convenient for transportation.

Before the transportation and use of most powder materials, it will be pressed and formed, and then in the follow-up work, the main equipment for pressing and forming is a ball pressing machine, but in the actual production process, there will always be some balls with rough surfaces and burrs How to operate to ensure the smoothness of the ball? The following small will introduce several methods:

1. Regularly clean the ball socket of the roller

When pressing some materials with high water content and requiring the use of binders, due to high temperature and high pressure, etc., the powder of some materials will inevitably adhere to the ball socket of the roller skin of the peat briquette machine, resulting in rough defects on the surface of the subsequent pellets. , or virtual balls that cause subsequent pellets to form balls. Therefore, when dealing with such materials, it is necessary to clean the roller skin of the briquette machine regularly. It is required to use brushes, soft shovels and other tools to remove the residual material powder in the ball socket of the briquette machine when the briquette machine is stopped and the power is cut off. Be careful not to use any corrosive cleaners, wash with water.

2. Adjust the ball socket

Sometimes the ball sockets on the two roller skins of the peat briquette machine are not in contrast, and a slight misalignment will cause the pellets to have burrs, and in severe cases, the finished briquette balls will be unqualified, resulting in misplaced products. At this time, it is necessary to adjust the two rollers and the bearings of the two roller skins, so that the bearings can be compared with the points of the baseball socket. In this way, the pellets extruded by the briquette machine will not have burrs, and after adjustment, there will be no deformation and slag during transportation.

3. Reduce the gap between the rollers

When the gap between the two pairs of rollers of the peat briquette machine is large, the contact area of the material between the two pressure rollers is reduced, and some materials are not pressed by the pressure rollers, which will cause the balls of the briquette machine to have burrs. In order to deal with this situation, you can adjust the roller gap of the briquette machine. Be careful not to make the gap between the two roller skins of the briquette machine too small. Too small and too tight will cause the two rollers to die and cannot rotate, which will also reduce the peat pressure. The life of the roller skin of the ball machine.

Goman peat briquette machine has more than 10 types of large, medium and small models, with an hourly output ranging from 3 to 45 tons and a price ranging from 10,000 to 100,000. Users can order according to their own production needs.

If you want to know about more briquette machine, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

Have you understood the reason why the briquette machine fails to press the ball?

The briquette machine mainly presses various powders, powders, waste materials, waste slag, etc. All powdery materials that need to be sintered need a briquette machine, which is widely used in refractory, power plants, metallurgy, chemical industry, energy, transportation, heating and other industries. It does not need to add water, and the ball forming rate can reach as high as 99%. Common The shapes are: square, heart, spherical egg, round, goose egg, pillow, etc., which can be pressed into balls at one time, with small investment and large processing capacity.

Have you understood the reason why the briquette machine fails to press the ball?

During the use of the ball press equipment, sometimes there will be problems of not forming a ball or not forming a ball. The reasons for this problem are usually insufficient material supply, too small hydraulic pressure, soft quenching of the roller skin, and deformation of the ball socket.

1. Insufficient material supply will cause the material of the briquette machine to be pressed, so it is necessary to add enough material for the briquette machine;

2. If the hydraulic pressure is too small, the material will not be fully compressed, which can reduce the speed of the main engine and increase the working pressure of the system;

3. The low quenching hardness of the roller skin will reduce the forming pressure of the briquette machine, and the surface quenching heat treatment of the roller skin can be carried out or the roller skin can be replaced;

4. The deformation of the ball socket will make the shape of the material uneven, and it must be repaired or replaced in time.

The briquette machine produced by Goman is stable in operation and low in cost, which fills in the shortcomings of traditional equipment. On the one hand, it meets the needs of the domestic market, and on the other hand, it also forms a style with its own characteristics. Under the new economic development situation, the establishment of the briquette production line has also received policy and economic support. Perfect investment will generate huge economic benefits and profit margins. Rectification of high-emission and low-efficiency industrial enterprises has become a policy development priority. New Direction.

If you want to know about more briquette machine informations, you can visit our website: https://www.sinobriquettemachine.com/briquette-machine/

[sinogomine]

What to do if the briquette machine sticks the ball?

Briquette machine is a kind of briquette machine equipment that is more common among many types of briquette equipment. The advantage of  Machinery's briquette machine is that its power is larger than that of general briquette machine. Now it is often used It is used by some mineral powder application enterprises. Mineral powder briquetting machine equipment should learn to use and maintain normally, which can better improve our work efficiency and reduce our production costs. In the processing of metallurgy, mining, and municipal waste treatment industries, the ball press machine, as the main molding equipment for materials, has always been one of the main mechanical equipment researched and improved by people. The high-quality ball press machine can effectively and quickly process materials into Balls provide convenience for subsequent transportation and reprocessing, but due to some reasons, many friends will always stick to the ball when they use the ball press machine to produce, so what should I do if the ball sticks to the ball press machine?

If you want to solve the phenomenon of sticking balls in the briquette machine, you must first figure out what causes the sticking balls. The editor of Machinery sorted out several common causes of sticking balls for you through on-site understanding, and the specific influencing factors It can be divided into equipment factors and material factors.

1. Equipment factors of briquette machine

(1) Dislocation of ball and socket

The asymmetry of the rollers of the coal briquette machine, or the discrepancy between the ball sockets on the two rollers, is generally called ball socket dislocation. If the misalignment of the ball socket is not serious, the processed finished ball will have burrs. If the misalignment is serious, the finished ball will be unqualified, and a "deformed ball" will appear. Most of this ball directly contacts the surface of the roller skin. It will stick to the roller skin at high temperature.

(2) Gap between rollers

Improper adjustment of the gap between the rollers of the briquette machine is also the main equipment factor causing sticky balls. When the gap is too large, the material will produce annular deformation after being processed between the two rollers. This annular deformation will also stick to the roller skin and be difficult to fall off due to the large contact surface with the roller skin; but when the gap between the two rollers If it is too small, it is easy to cause the two rollers to lock due to excessive friction and reduce the service life of the roller skin.

(3) Roller speed

The speed of the rollers of the coal briquette machine directly affects the output of the equipment and the residence time of the material in the ball socket after forming. When the rotating speed of the counter-roll is too low, the material will be squeezed in the ball socket for a long time, and sticking balls will appear as the time and temperature change; and reduced ball quality.

2. Material factors

In addition to the reasons of the briquette machine equipment, in the process of production and processing, the improper mixing ratio of the materials before processing will also cause the ball sticking phenomenon of the briquette machine, which mainly occurs in the moisture content and the amount of binder inside the material. .

(1) Material moisture content

In the process of balling the material, too much moisture inside the material is very unfavorable to the de-balling. The over-humid material will become viscous under the high temperature of extrusion, resulting in the phenomenon of sticky balls and hemispheres, but too little water It will cause loose balls and no shape when demoulding, so the moisture control of the material is very important.

(2) Material binder

Some materials have poor self-binding ability, so a certain amount of adhesive will be added before extrusion molding, and too much adhesive is an important cause of sticky balls. When the material is extruded, the pores inside the material will be fully squeezed, and the excess adhesive will fill the entire ball socket, so when the mold is demoulded, it will be due to these gaps between the finished ball and the ball socket. The sticky ball phenomenon occurs due to the adhesive. The solution to the sticking phenomenon of the briquette machine is mainly to take preventive measures in advance, which requires the control of the entire process from material proportioning to briquetting machine forming, which is specifically reflected in the following aspects:

1. Before production and processing, the briquette machine should be tested and inspected. When the ball socket is dislocated, the roller and the roller skin should be adjusted symmetrically according to the ball socket adjustment method of the briquette machine;

2. Set the correct pressure of the ball press. If the pressure is too small, the density and strength of the ball will be affected due to insufficient compression ratio, which is not good for demoulding. If the pressure is too high, the load and energy consumption of the equipment will be increased, resulting in waste of resources;

3. When mixing materials, the water content should be controlled between 5% and 9%. Even if the material needs more water, the water content should not exceed 10%. At the same time, the selected adhesive should have It has the characteristics of good viscosity and strong wettability, and fully considers its chemical composition and cost to determine the usage amount;

4. The impurities in the material will reduce the binding force between the particles of the material during the compression process, resulting in virtual balls when demoulding, so the impurities in the material should be completely removed as much as possible;

5. During the ball forming process, the material supply above the two rollers of the briquette machine should be sufficient, uniform and stable to ensure constant pressure on the roll gap, so that the ball shape is always in a full state, ensuring the ball forming rate and quality.

If you want to know about more briquette machine informations, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

What should I pay attention to in the use of desulfurization gypsum briquette machine operators?

 The operator is the key person in the plant of desulfurization gypsum. Not only controls the operation of the desulfurization gypsum briquette machine and its entire production line equipment, but also has a vital position for the goodness of the finished ball. Therefore, the production efficiency of a strong professional operation level and experienced operator is much higher than much. What jobs are the operators who should pay attention to in suppressing production?

The operator of the equipment must first be familiar with the process and operation process of the equipment, check whether the suppression of the component is sufficient pressure, hit the pouring mixer switch into the automatic state, determine the sampling port, turn off the water valve For personnel contact, according to the ratio and the mold height.

Secondly, in the process of suppressing the materials, it is necessary to determine that all the raw materials are added in a sufficient amount, and control the pressure, molding and other factors to work. Moderate adjusting the suppression parameters and molding models to ensure that the desulfurization gypsum pressure machine can work smoothly. Pay attention to the normal application of the equipment and the accurate adjustment of the ingredients during operation.

Also, when the pressure of the device reaches the standard, the feed can be carried out. When running for 3-5 minutes, when the temperature reaches 42-45 ° C, start the material. After the material is finished, stir for 20-30 seconds for suppression. After the production is stopped, the valve is turned off. When the production is completed, the mixer and the auxiliary equipment are cleaned. After the cleaning is over, the all valves are turned off, and each switch is hit to the state.

The entire plant of briquette machine was successfully completed. During the suppression process, the abnormal phenomenon of desulfurization gypsum briquette machine was completed. Please disconnect the power immediately to remove the material and ensure that the material is not damaged. Contact our technicians to perform maintenance.

If you want to know about more briquette machine, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

How to improve the ball strength of the clay briquette machine?

The intensity of the clay briquette machine is a key factor that ensures that the clean coal is not broken during storage and transportation. A key judgment criterion is the strength of the coal that is pressed by the device. However, in addition to buying good -quality equipment, the ball strength is also related to many factors. So how to improve the ball strength of the coal pressing machine?

Select the appropriate coal adhesive. After selecting the coal -type raw material, the coal -type coal manufacturer must conduct an experiment of the coal -type coal adhesive. The suitable coal adhesive is an effective guarantee for the strength of the coal -forming ball.

The degree of wetness and humidity of raw coal usually adds an appropriate amount of moisture and water to the production of lubricants in the production of coal production, reducing the internal friction of the molding system, and increasing the mechanical strength of the coal -type coal. If the hydrophilic bonding agent is selected, the appropriate amount of water will wet the surface of the particles in advance, and the use of mutual bonding between particles is used. The more suitable molding moisture is usually 10-15 %; if the hydrophobic adhesive is selected, the moisture will reduce the effect of the adhesive, so at this time, the moisture that controls the material is less than 4 %. In general, the moisture should be flexibly grasped according to the specific situation and control it within one range.

The crushing process of coal -type raw materials becomes vital in the entire coal production process process. Whether the broken material granularity level after crushing is reasonable, it also determines the quality of the future coal products. ≤3mm, so what kind of crushing machines to choose in the production of type coal are a key issue to consider.

The proportion of raw materials in the production of coal production is very important, and the degree of uniformity in stirring is also particularly critical, which directly affects the ball strength of the clay purse machine. Therefore Link.

The above four points are a few key issues that should be paid attention to before entering the clay briquette machine. It is a favorable guarantee for improving the forming of the equipment -type coal. Use and transport.

If you want to know about more briquette machine, you can visit our website: https://www.sinobriquettemachine.com/briquette-machine/

[sinogomine]

How does the mud briquette machine cool the heat when running?

Mud briquette machine are a type of new technology equipment specifically suppressed by various types of powders. It can effectively save the amount of minerals and purify the environment. But when the device is running, there is a problem that must be paid attention to, which is heat dissipation.

Many customers do not pay attention to these details when applying the device. They think that this is needed to be considered when the device is designed. It does not need to pay attention to it. This idea is outrageous. I believe everyone knows that as long as the device is running, it will produce very large calories. It is not except the clay pressure pill machine, and the time will not be short as long as the equipment runs. Although the equipment itself has a certain heat dissipation function, However, this cannot meet the overall heat dissipation needs, so it is necessary to pay attention to it, otherwise it will be able to shorten the life of the entire equipment under the condition of not in place in the condition of not in place for a long time. The part of the part is burned and the device is broken.

In order to avoid this situation, when installation, strictly follow the electrical specifications, each line must go well to avoid interference. When configured the fan, try to configure the dual heat dissipation fan, so as to have a better effect. Try to put a powerful fan next to the device, so as to double the heat dissipation problem of the clay pressure machine. If there is a problem with the equipment, the operation is suspended.

In general, the heat dissipation of the mud briquette machine is very important, especially when the weather is stuffy in summer, it is necessary to step up protection, but this does not mean that it is cold in winter. A little standard, if the situation is cold, the device is also prone to problems for a long time. Do not ignore this problem, because if the internal components of the equipment are burned due to overheating in the equipment, then the replacement accessories are more troublesome, and it takes time to consume time. Strive, also spend money.

If you want to know about more briquette machine, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

How to ensure that the finished balls of the ore powder briquette machine are not broken or broken?

When producing, the ore powder roller press briquette machine will encounter a problem of low success rate and easy finished product. So what are the factors of this problem? How to ensure that the finished product balls are not broken before they are put into use?

We know that the key component of this device is the roller. The roller suppression of the ball after storage, loading and unloading, and the unavoidable part of the transportation session must suffer from all kinds of squeezing and external force. Only high ones are high. Stress strength can avoid damage.

So how to produce the finished product of the production of mineral powder ball press? The success rate of the finished product of the equipment is related to the setting of the roller's direct distance. When setting the equipment to the roller gap, the spacing ratio of the two pressure rollers should be inversely proportional.

There are some manufacturers to reduce the volume of the equipment to the roller pressure, which reduces the spacing of the roller. In this way, there is an error. Although the distance can be reduced, it can improve the forming pressure. It is not easy to cover the ball bowl, so it will endanger the quality of the ball, and then it will not be able to make the ball.

When the spacing of the ore powder press briquette machine is too large, the formation pressure has not yet been transmitted to the management center of the coal ball, and the mine powder will fall off, which will not only harm the strength of the ball, but also cause the ball to be too thick. There are many burrs, many powder dandruff, and even the ball will not be over. Therefore, when the equipment is installed up and down the upper and lower pressure rollers, it is necessary to pay attention to adjusting the distance between the two. According to different materials, there should be different distances. Generally, it is advisable to control 2-3.

When designing the ore powder press briquette machine equipment, you need to control the equipment speed. You must not be too large or too small. If the speed of the speed of its pressure roller can increase the force of the material on the pressure roller, it is beneficial to transmit it in turn, to promote the middle closer to the middle of the material particles, and it can get rid of the shear stress caused by the interface of the ball bowl, and then thereby It can improve the strength of the powder, but if the equipment speed is too low, it will cause the finished product to shatter, resulting in a significant reduction in the output of the ball.

If you want to know about more briquette machine informations, you can visit our website: https://www.sinobriquettemachine.com/briquette-machine/

[sinogomine]

How to increase the output of clay briquette machine?

1. Ensure equipment performance

No matter how high the capacity of the clay briquette machine, if the quality is not up to the standard, there are often problems in operation, then the production capacity must not be satisfactory. In addition Essence Therefore, when purchasing, you must choose to produce regular large brand manufacturers. In addition, check and maintain before starting application, and operate in accordance with standardized operations.

2. Production line equipment production capacity matching

Equipment with high capacity alone cannot be produced in large -scale production. Therefore, companies will establish production lines, and there are many components of production lines. In addition to these devices, there are crusher, conveyor, dryer, etc. The production capacity of the production line equipment must be matched with the production capacity of the clade pressure machine, so that it will not cause waste of equipment resources.

3. The operation and connection of the production link should be smooth

Everyone knows that the production line is a complete whole. Any equipment or personnel in it is part of this whole. If there is a problem with any link, it will affect the output of this production line, or even employee safety. Therefore, in the production process, it will be safe. Therefore, in the production process Among them, the performance and safety of each production line equipment must be ensured. In addition, the smoothness must be ensured in each link. The results caused by each link should be corresponding to the beginning of the next link, so as to improve production efficiency.

4. Enhance the speed of the equipment to the roller

The roller speed of the clay briquette machine determines the speed of material forming, but the corresponding pressure must be given, otherwise it will affect the quality of the molding. It can only be done in the case of molding quality.

If you want to know about more briquette machine informations, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

The reasons and solutions of the edge of the finished ball group of the clay briquette machine

During the production process, the mud ball briquette machine, because of the long period of operation, the impurities of the equipment itself or the high hardness in the material may cause the device pressure roller to be mild. I will introduce the specific reasons and solutions to this situation:

Reasons 1: There are gaps in the middle of the two pairs of rollers. If there is a gap between the two rollers, the material in the contact area of the two pressure rollers is reduced. Some materials have not been suppressed by the pressure roller, which will cause the edge of the equipment of the equipment to be smooth.

Solution: You can adjust the roller gap of the clay pill briquette machine. Remember that the two roller skin of the equipment should not be too small in the middle. If it is too small, it will cause the two rollers to hold the death. And also reduce the life of the roller skin of the equipment.

Reason two: The ball nest on the two roller skin of the equipment does not have a center control. If the ball nest and the ball nest do not have a center control, the mild will cause the side of the finished ball to not be smooth. It is the misplaced product of two semi -ellipses.

Solution: Regulate the two rollers. What needs to be adjusted is the bearings of the two roller skin to adjust the two -roller leather bearing, so that the two bearing and the center point of the two stick balls are compared, which is the center control. In this way, there will be no smooth conditions on the edge of the finished ball group.

In order to better play the effect of the use of clay pilling briquette machines, we must pay attention to the quality of the finished ball during the production process. The edge of the ball is not smooth. It is necessary to stop and adjust it in time to avoid the quality of the finished balls. Essence And avoid minor problems that lead to worn other components, bringing greater economic losses.

If you want to know about more briquette machine informations, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

Causes and solutions for blocking the coal briquette machine

The molding problem of coal briquette machine has always been a topic that everyone pays more attention and discuss. Because it is related to the quality of corporate coal products and production efficiency. The materials in the process of materials are not good for obstruction and molding, and friends in the industry are not unfamiliar. Xiaobian specially consulted professional and technical personnel for some reasons that caused this phenomenon, and how they could solve them well.

1. The water content of the type of coal material is too high

Everyone said before that in the process of suppression, if the material is too dry, the coal briquette machine is not easy to suppress, and the molding strength of the ball eggs is not high. If it is too wet, it is easy to cause adverse obstruction and demolition. If you think about it, you can also understand that the water content is high, and the stickiness of the material is large, so the chance of the adversely obstructive and de -molding of equipment will increase.

2. The equipment roller leather ball nest is not very smooth

If the ball nest is not very smooth, there will be a certain friction with hair edges, so the material is easily attached to it. The device is not good.

3. The size and depth of the equipment ball nest are unreasonable

This is the reason for the equipment itself. The size and depth of the roller skin are unreasonable. For example, if the ball nest is too deep, it will be difficult to go out after the material is forming. Because the roller can replace it, we can replace the more suitable roller skin to solve it.

4. The problem of the equipment feed system

There are three major parts of the coal briquette machine, which are feeding, transmission and molding. Therefore, if a problem occurs, it is easy to cause obstruction.

If you want to know about more briquette machine, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

How to reduce the energy consumption of clay pilling briquette machines?

Clay pilling briquette machine can be fully suppressed to all kinds of coal coal, coal powder, lignite, non -tobacco coal, sticky coal, slag and other powdery materials. Many customers will definitely encounter the problem of too much energy consumption when applying this device. So how to reduce the energy consumption of the device?

1. When purchasing equipment, you should first consider choosing high -efficiency energy -saving motors, and then consider the remaining performance indicators as needed to save power; reasonably install the concrete voltage ball machine parallel to low voltage capacitors for no achievement compensation, effectively improve the power factor, reduce the absence of nothing Power loss, saving power.

2. Improve the efficiency of the equipment motor itself. For example, if the motor is changed from the cold fan to the remaining cold fans, it can stop using the cold fan control in winter when the load is very small or the outdoor motor is used in winter, which is beneficial to reduce energy consumption.

3. Change the stator winding into a triangular mixed serial winding, and convert the star -shaped connection method or triangular connection method according to the load weight, which is beneficial to improve the magnetic potential waveform produced by the clade pressure ball winding machine and reduce the current of the winding. The purpose of energy saving.

4. Select the remaining continuous speed adjustment operation methods. Such as the application of pressure regulators, variable pole motors, electromagnetic coupling speed, variable frequency speed regulating device, etc.; Reasonably adjust the equipment motor supporting application, which can enable the motor to operate in high -efficiency working zones to achieve the purpose of energy saving.

The same method can also be used for the remaining equipment of the production line of clay pilling briquette machine, especially in summer. The maintenance customers of the motor should pay more attention to reduce the energy consumption of equipment and improve production efficiency and economic benefits.

If you want to know about more briquette machine, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

Why is the price of a powerful briquette machine so big?

Product quotes have always been a topic that customers are more concerned. Except for the different power pressure briquette machine, many customers have a large price of disparity for such equipment. So why are the prices of such equipment so much? Where is the difference?

I. Equipment model production capacity: The equipment has different models. The output, technical parameters, shape size, and body weight of each model are different. The cost of equipment production is different, so the sales price is different. The production capacity and output are similar. It refers to the amount of materials that the equipment can produce per hour. Of course, the price of equipment with large production capacity will certainly be more expensive than the equipment with smaller production capacity!

2. Equipment quality: Each manufacturer has a large difference in the technology, raw materials, and production processes selected by the manufacturer. These factors affect it. The lower the chance of failure, the longer the period of use, and the price higher at the same time.

These two aspects are the leading factors that affect the price of the device. In addition, the following factors will also lead to the disparity of its price:

1. The impact of manpower on equipment prices: Designers, welders, etc. who need to produce such equipment need to pay wages and various insurances.

2. Manufacturer: For manufacturers operated by small factories, their production technology is simpler and the equipment quality requirements are not strict and the production costs are reduced. The powerful ball press produced by large manufacturers will have strict regulations in designing, workmanship, and material options. Coupled with the cost, the price is of course higher.

3. After -sales service: After the equipment is issued, there will be a warranty period, and the scale manufacturers will have after -sales protection. Of course, the cost is of course added to the equipment price.

4. The treatment cost of waste can also affect the price of equipment. In my country's advocating environmental protection and energy conservation, it has increased the cost of equipment manufacturing.

5. Manufacturer's business method: Each manufacturer's business method is different. Some powerful ball machine manufacturers use the concept of small profit -making sales to increase the sales volume of the equipment with small profits, thereby increasing the market share. From In the long -term angle to operate enterprises, and some are intermediate agents, with the help of price increases to take intermediate profits, the price differences in the two types of methods will be relatively large.

If you want to know about more briquette machine, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/

[sinogomine]

The maintenance ruler of the strong roller briquette machine?

After a certain period of time, a powerful briquette machine will have various size problems, which affects the efficiency of coal forming, and the repeated maintenance is not very good, resulting in the continuous improvement of equipment costs. The reason is that there is no maintenance of equipment maintenance. As a result of the maintenance of maintenance work, Xiaobian here sorted out the maintenance ruler of the device for your reference.

1. Daily inspection and cleaning

(1) Check whether the foundation and safety bolt are loose and tighten them; turn on the inspection cap of the reducer to check the gear tooth harmony and wear.

(2) The oil pressure of the powerful briquette machine shall be stopped. If there are pressure changes caused by temperature changes, oil leakage and other reasons, you should inject new oil or run back to modify the period of oil pressure. The oil pressure system should be stopped immediately, and the oil leakage should be fixed before running.

(3) Check the equipment of the equipment regularly to ensure production safety.

(4) Pay attention to the dust of the equipment up and down in time. During the disassembly process, you should also pay attention to dust removal. It is strictly forbidden to infiltrate the movement of the device.

(5) If you find that there are too many dust, clean it in time.

(6) Do not turn on the equipment for a long time, remove the balance of each part.

(7) The transmission chain of the device is cleaned once a month.

2. Timely replace and supplement various oils

(1) Replace gear oil on time, and the gear box should be injected twice per shift.

(2) The reducer in the powerful briquette machine device should replace gear oil every three months. To ensure the normal operation of the equipment.

(3) Check the lubricating oil of each transmission device in the equipment regularly.

(4) The bearings of each part of the equipment should be added once a year.

(5) The movement of the bearing is injected once a month, and it must be cleaned once after half a year.

3. Timely replace the wear parts

The worn parts should be replaced or repaired in time to avoid damaging other components when continuing to apply. The roller skin of the powerful briquette machine is used as a damaged part. It is necessary to check whether the roller skin is worn on time, and whether the roller skin is aligned. If the roller skin is worn or inconvenient, it should be replaced and repaired in time.

If you want to know about more briquette machine, you can visit our website: https://www.sinogomine.com/Briquette-Pressing-Machinery/