rotorootergreenevilletn

[rotorootergreenevilletn]

What Plumbing Is Needed For A Bathroom Sink?

Two fixture holes on 4-, 6-, or 8-inch centers are common in bath sinks. The wider types are designed to accommodate a split-set faucet, which separates the faucet handles from the spout. A center set or a single-lever faucet can be installed in the 4- or 6-inch holes. Flexible supply tubes transport water from wall shutoff valves to threaded tailpieces at the faucet’s base.

  A pop-up stopper is commonly installed in the drainpipe that goes through a bathroom sink, and it raises and lowers as you pull up or down on a knob or handle just behind the faucet body. The knob is actually the head of a lift rod that is connected to a clevis (a connecting bar). The clevis is attached to a pivot rod-and-ball assembly, which comprises a rod that goes through a rubber pivot ball and slopes uphill to the stopper’s tailpiece.

  The pivot rod pushes the stopper up when the knob and lift rod are pushed down; the pivot rod pulls the stopper down when the knob and lift rod are pulled up. If you wish to get rid of the assembly, you might be able to just pull it out. To detach it from the clevis, you may have to twist it.

  A flange on the sink drain is sealed to the sinkhole with the plumber’s putty. This flange is screwed into the drain body, which is held in place by a locknut on the underside of the sink basin.

  Slip-joint couplings connect the tailpiece, which can be attached to a pop-up stopper, to a drain trap. To prevent sewage gasses from entering the room, a sink trap is filled with water and attached to a threaded nipple inserted in a T in the drain line. The connection is concealed by an escutcheon trim.

  A set of levers and rods controls a mechanical pop-up stopper. If this isn’t working properly, the answer is generally as simple as adjusting the clevis screw or pivot rod location.

[rotorootergreenevilletn]

Plumbing Vent FAQs

Most homeowners will experience a plumbing problem at some point, but identifying the issue is more than simply inspecting the water lines. Plumbing vents can clog or be damaged, resulting in stoppages and a variety of other problems. It’s critical to understand this delicate aspect of your plumbing system if you want to maintain your drains running efficiently in your home. We’re here to answer some of the most often asked inquiries concerning plumbing vents by homeowners.

What Is A Plumbing Vent?

Your plumbing system’s air pressure is controlled by the plumbing vent, often known as a vent stack. The plumbing vent pipe, also known as a plumbing air vent, eliminates gas and odors from your home in the same way as drain pipes remove water and waste. It also enables fresh air into the plumbing system, which aids in the smooth flow of water through the drain pipes. The plumbing exhaust pipe, on the other hand, does not carry any water. It’s a vertical pipe that connects to a drain line and travels through your home’s roof. The pipe leading to the primary roof vent is known as the vent stack. It helps maintain proper atmospheric pressure in the waste system by channeling exhaust gasses to the vent.

What Are The Benefits Of Plumbing Air Vents?

The plumbing system in your home is designed to remove water and waste as effectively as possible. Its drainage and venting systems are actually two separate systems that work in tandem.

Drainage pipes transport waste from your home to a septic tank or the city sewer. When a toilet is flushed or a sink is drained, vent pipes deliver fresh air to each plumbing fixture in the house, assisting the system in moving water through the drainage pipes.

Plumbing air vents also allow wastewater gas and stink to escape while preventing sewage gasses from entering the dwelling. So that the vapors can quickly dissipate, plumbing vent pipes are situated on roofs, away from windows or air conditioning units.

What Can I Do If I Have a Problem With My Plumbing Vent Pipes?

Your home’s plumbing drainage system will not function properly if your plumbing air vents or vent stacks do not work properly. A blocked vent could be the cause of gurgling sounds coming from your drains, standing water in your sink or bathtub, or a slow drain in the bathroom or kitchen. Negative pressure develops up in drainage pipes when a plumbing vent pipe or vent stack is stopped, interrupting water flow. Though you may be able to clear a clogged drain on your own, if a blocked vent is to blame, stoppages will continue to occur. Sediment can accumulate inside drain pipes as a result of frequent stoppages and slow drains. This might cause more damage to your plumbing system, resulting in costly pipe repair or replacement.

A vent obstruction can be severe if you can’t clear a slow-flowing drain using a plunger, auger, or drain cleaner. A vacuum will result if the plumbing air vent or vent stack becomes entirely clogged, and you will no longer hear gurgling. Sewer gasses will also be detectable in the rooms where the impacted fixtures are located. This is a problem that has to be addressed right away by a plumbing specialist.

[rotorootergreenevilletn]

Museums and Attractions In Greenville

When you visit Greenville, you’ll feel as if you’ve taken a step back in time. Greeneville, being one of Tennessee’s oldest cities, has a rich history that you can learn about and enjoy through the city’s many attractions. All around the area, there are fascinating museums and historic sites to visit. Apart from the history, the town’s many arts and culture activities, such as the theater and arts center, will keep you entertained. Keep yourself occupied in Greeneville, TN with the greatest things to do.

The City Garage Car Museum 

The City Garage Car Museum is a local auto museum with a private collection of historic automobiles as well as a retro cafe. When you see the unique vehicles on exhibit in this museum, vintage car fans will go crazy. A 1969 Excalibur, NASCAR race cars, and even a 1981 DeLorean are among the vehicles on display (perfect for Back to the Future fans). Visit one of the museum’s themed cafés for a break. To complete the experience, they have parked vintage cars outside their diner. The Texaco Service Station, a historic petrol station adjacent to the eatery, is well worth a look.

Greeneville Antique Market

Greeneville Antique Market is a small antique market with three floors to browse in downtown Greeneville. This is the spot to go if you enjoy looking for unusual things to see in Greeneville and other places. The 75 booths inside the store contain many one-of-a-kind and uncommon items, ranging from antique furniture and primitives to old books and records. Make a list of things you enjoy and where you can find them, then keep looking. When it’s rainy or chilly outside, exploring the entire shop is a pleasant and easy indoor activity.

A wise buyer’s recommendation is to acquire only what you absolutely need after you’ve completed all three floors.

The Andrew Johnson National Historic Site

President Andrew Johnson is commemorated in the Andrew Johnson National Historic Site, a 16-acre facility dedicated to him. History buffs will love walking around this location because it includes a visit to President Lyndon B. Johnson’s homestead, which is furnished with many of his family’s original things. Because they’ll learn so much about the country’s past leader, the guided tour is one of the best things to do in Greeneville with kids. Visit the Early Home, which is where President Johnson and his wife started their family, in addition to the Homestead. It was also the home of the late president during his early political accomplishments.

The Niswonger Performing Arts Center 

The Niswonger Performing Arts Center is a huge theater that hosts live performances. Seeing a dynamic show in this venue is constantly on the list of top things to do in Greeneville at night. You’ll have a great time while you’re here, with everything from rock concerts to deep country performances.

If you want to sit in the front rows of the Center Mezzanine or the Center Balcony for a low price, try the front rows of the Center Mezzanine or the Center Balcony. Even though you’ll be further away than Orchestra, you’ll have an uninterrupted view of the stage because no one will be seated in front of you.

Margarette Falls

Margarette Falls, in Cherokee National Forest near Greeneville, is a 60-foot fan-shaped waterfall. The 2.4-mile journey to the cascades is full of lovely forest vistas, clumps of stunning wildflowers, and a rushing river, all of which are must-see sites for nature lovers this weekend. The stunning waterfall is the icing on the cake and might be regarded a prize for completing the trail. While the route is well-kept and one of the beautiful spots to visit in Greeneville, hikers should exercise caution. In a few spots, you may have to scramble, and other areas are narrow and rocky. However, it should be reasonably simple and ideal for day trips.

[rotorootergreenevilletn]

The Best Weekend Getaways from Greenville

Greenville is the county seat of Greenville County, and while it has its fair share of attractions, you might want to take a day excursion outside of town. If that’s the case, you’re in luck: Georgia, Tennessee, and North Carolina are all within driving distance, and you may choose from huge cities, rural agricultural regions, and historic towns. It’s also not difficult to go to the Blue Ridge Mountains, where you may visit quaint mountain towns, marvel at the grandeur of pristine lakes and waterfalls, and trek to your heart’s content. Certain attractions may be closed temporarily or require reservations in advance. Currently, some eateries only provide pickup. It’s possible that the hours and availability have changed.

  1. Asheville

Asheville, located in the Blue Ridge Mountains of North Carolina, is an unquestionably gorgeous city that attracts nature lovers from all over the world. The Appalachian Trail and the scenic Blue Ridge Parkway are both easily accessible, whether you like to walk or drive. The city is also a haven for art aficionados, with dozens of galleries and museums downtown, as well as the River Arts District, where you may visit artists’ studios directly. The beautiful Biltmore estate, the Basilica of Saint Lawrence, and the several local microbreweries are among the town’s other attractions.

2. Athens, Georgia

The town of Athens, which is home to the famous University of Georgia, has a lovely Victorian-era historic area packed with antebellum structures, an amazing array of locally owned cafés and restaurants, and a strong dose of southern-style charm that makes visitors want to linger longer. If you’re here in the evening, try to see a performance at the Georgia Theater, the 40 Watt Club, or one of the other highly-acclaimed venues in town, which has given birth to the likes of R.E.M. and the B-52s.

3. Charlotte

Charlotte, North Carolina’s largest city, is a rapidly growing metropolis with a plethora of restaurants, stores, and attractions to offer visitors. Locals refer to the current downtown core as Uptown, which is dotted with soaring buildings and high-profile attractions such as the NASCAR Hall of Fame and the Levine Museum of the New South. The funky areas of Plaza Midwood and North Davidson, known to locals as NoDa, are where you’ll find the majority of the city’s greatest restaurants and businesses, but if you’re seeking to immerse yourself in art and culture, head to NoDa.

4. Columbia

Columbia is notorious for its blazing summer temperatures, but that’s not the only reason it’s dubbed “The Real Southern Hot Spot.” The city is home to a diverse range of busy restaurants, sophisticated cocktail bars, and stylish retailers, but it also provides a welcome look into the city’s rich history. Historic home museums may be located all over town, and the South Carolina State Museum is an excellent site to learn about history in general. The Riverbanks Zoo and Garden, which is especially popular with families, is another popular destination for those vacationing with children.

5. Easley

Easley is easily the largest city in Pickens County (pun entirely intended) and an ideal day trip destination, is located at the base of the Blue Ridge Mountains. On Saturday mornings, the friendly downtown streets hold a weekly farmer’s market, and they have a decent assortment of restaurants, antique shops, and specialized stores open all week. A children’s splash park and an outdoor amphitheater, which frequently holds festivals, live music, and other special events, are among the town’s other facilities. The adjacent Blue Ridge Mountains, with its many lakes, waterfalls, and picturesque hiking paths, are also easily accessible to visitors.

[rotorootergreenevilletn]

Best Tourist Spots in Greenville, TN

Greeneville, founded in 1783, is unlike any other town in Tennessee. This community is Tennessee’s second oldest and has a rich historical and cultural history. A stroll around this village may make you feel as if you’re in a novel. A community rich in natural beauty may be found amid the churches, attractive residences, significant historic sites, and brick pathways. This town has all of the conveniences of a major city, including Airbnb vacation homes, while still maintaining the sense of a small community. 

Here are some major tourist attractions in Greeneville Tennessee:

City Garage Car Museum

The City Garage Car Museum is a premier institution with a large collection of historic vehicles to tour. This museum, which has everything from a 1914 Ford Brass T Model to a 1969 Excalibur, is a must-see for anybody who is interested in vintage rides. Apart from the automobiles, the museum has a “mini-village” with signs, pumps, and a stoplight. Kent Bewley created the museum in 2009, and it is a must-see for automobile enthusiasts and non-car enthusiasts alike. You can capture a ton of Instagram-worthy photos while having a fantastic time.

  Niswonger Performing Arts Center

Niswonger Performing Arts Center is a wonderful location for individuals who like the performing arts. For many years, the Greeneville Arts Center has hosted events and activities for the community. This facility is perhaps Greenville’s cultural, civic, and artistic hub. Enjoy the lively atmosphere and excitement created by the numerous performances that take place on a regular basis.

Andrew Johnson National Historic Site

After Abraham Lincoln’s assassination, Andrew Johnson became President of the United States, and this site is named after him. The Andrew Johnson National Historic Site, located at the crossroads of College and Depot streets, is home to a variety of attractions. Andrew Johnson’s two homes, his tailor shop, and his ultimate burial place are all open to the public. The Visitor Center sells tickets to the Andrew Johnson Homestead. Take a stroll around the house where this remarkable guy lived to see original family heirlooms and mementos.

  Dickson Williams Mansion

During the Civil War between 1815 and 1821, the Dickson Williams Mansion was erected and served as a seat of administration. Because it changed hands multiple times during the conflict, the Federal-style architectural jewel served as headquarters for both sides (Union and Confederate). This mansion is said to have hosted presidents (Jackson and Polk), famous personalities such as Marquis de Lafayette, Henry Clay, and others during its heyday. While attempting to flee the mansion, Confederate General John Hunt Morgan was slain by Union soldiers in the garden. You can look around the restored furniture in the room where he slept and learn about the history of this unique home.

[rotorootergreenevilletn]

Tips to Disinfect Your Sink

Did you know that your sink is more than just a place to wash dishes? Disinfecting your sink is one of the easiest ways to prevent the spread of germs and bacteria. Disinfecting your sink will help keep your kitchen clean, safe, and healthy. This blog post will give tips on how to disinfect your sink with household products!

How to Clean a Kitchen Sink Without Using Harsh Chemicals

When cleaning the inside of your home, you should avoid using chemical cleaners. Chemical cleaning chemicals have potent scents and can cause headaches and eye irritation. If consumed, some are exceedingly harmful, even toxic. Chemical cleaners can pose significant concerns, particularly if you have small children or pets.

  Natural cleaning methods have grown in popularity as a result of these factors. They are much safer to use and have around the house, and they are really effective at cleaning. We’ll show you how to clean your sink without using harsh chemicals down below. These methods are extremely effective, and they may be used to clean both porcelain and stainless-steel sinks.

  Making Use of White Vinegar

No kitchen sink cleaning advice would be complete without including white vinegar. White vinegar is effective in removing oil, bacteria, and lime buildup. If you want to disinfect your kitchen sink, vinegar is also an option. White vinegar has the ability to eliminate microorganisms while not posing the same hazards as chemical cleaners. To clean your sink with vinegar, fill a spray bottle halfway with equal parts vinegar and water. Because vinegar is so versatile as a cleaner, it’s a good idea to keep a spray bottle on hand at all times. After giving your sink a clean washing to remove any debris, continue spraying the vinegar solution down the drain and wiping it dry.

  Using Lemon to Clean

Cleaning with lemon is another popular natural cleaning method. The procedure is quite straightforward. Simply cut a lemon in half or smaller slices and scrub your sink with the cut-up parts. Add some salt for further assistance; the coarseness of the salt will help shift any of the more difficult-to-remove items clinging to your sink. When you’re finished, rinse and dry the sink.

  Using Bleach to Disinfect Kitchen Sinks 

Caution: Do not use bleach in a stainless-steel sink. Bleach is corrosive to steel and can destroy your sink. Check the pipes under your sink if you have a porcelain sink. If you have stainless-steel pipes, avoid using bleach.

Vinegar is a dependable natural disinfectant, but if you want something with a little extra oomph, bleach might be the way to go. While a bleach solution is not recommended for stainless steel, it may be suitable for your porcelain sink.

[rotorootergreenevilletn]

5 Signs Your Toilet is Clogged

As soon as you notice that your toilet is taking longer than usual to flush, or if it’s not flushing at all, the first thing you need to do is find out what caused the clog. If there are signs of a clogged toilet, then it’s time to take action before things get worse! In this blog post, we will discuss five signs of a clogged toilet and how you can fix them.

Slow Draining Toilet

The slow draining of water from the toilet bowl after you flush is a significant indication your toilet is clogged, and your drains are backing up. The water level in the bowl will often take substantially longer than usual to drop, and the level may even drop lower than usual due to the suction effect of a clogged drain. Both are common indications of a clogged toilet and must be addressed immediately to prevent more damage. Your toilet should flush at the same rate every time, and any variation is a clue that something is wrong.

Overflowing or full toilet bowl

If your toilet bowl fills up after flushing, your toilet is clogged. A full bowl after flushing is the most reliable symptom of a clogged toilet. The most common reason is too much toilet paper or something foreign flushed down the toilet, such as a toilet deodorizer or children’s toys. This usually indicates that the obstruction is limited to the toilet trap and that the rest of your sewage drains are operating normally. However, do not flush your toilet again since this will result in a huge mess on your toilet floor. Call a professional to fix this for you.

Gurgling sounds coming from your toilet

Do you hear strange gurgling sounds coming from your toilet? If so, this may indicate a blockage in the vent pipe or another problem with your sewage drain. Water backing up and overflowing out of your toilet is definitely an indication that something is clogging up your drainage system. The most common causes are bath toys, children’s flotation devices, feminine hygiene products, or other non-flushable items flushed down the toilet. Another possibility is tree roots growing through cracks in the sewer line because of exposure to too much moisture for extended periods. Whatever it might be causing backflows can usually be fixed by plunging at home without expensive equipment needed by professional plumbers.

Bad odors

Bad smells coming from the drain are another sign of a clogged toilet. This can be due to an accumulation of organic material, which decomposes and releases bad smells into your home’s sewer line. Also, stagnant water sitting in the bowl will putrefy or develop harmful bacteria released by flushing once it gets stirred up again.

The post 5 Signs Your Toilet is Clogged appeared first on Roto-Rooter of Greeneville TN | Greeneville TN Plumbing Company.

[rotorootergreenevilletn]

Why Is My Garbage Disposal Leaking?

We’ve all been there. You are doing your dishes, and the garbage disposal starts to leak water onto your floor, or you’re cooking dinner and suddenly notice that there is water coming from underneath the sink. How frustrating! There are many causes for leaking garbage disposal (or dishwasher), but thankfully, we have some tips on fixing it!

A garbage disposal leak can occur in three places: the bottom, top, or side. The source of the leak is a good indicator of the severity of the situation. The required repairs are usually not with the waste disposal device itself but with the surrounding plumbing.

Garbage Disposal Leak From The Bottom

If you feel that your garbage disposal is leaking from the bottom, you’ll almost certainly need to replace it. But, before you jump to any conclusions, double-check that the leak is coming from the garbage disposal’s bottom.

Because the water travels, it’s possible that your disposal is dripping from the bottom but is leaking from the flange or dishwasher/drain piping. Dry your garbage disposal with a paper towel, then keep an eye on it to detect where the water is escaping.

The problem is the same whether your garbage disposal is leaking from the reset button, screws, or holes in the bottom. You have a significant issue that will almost certainly necessitate the purchase of new garbage disposal.

A faulty internal seal within the device is the most likely cause. Internal seals in garbage disposals safeguard the motor and keep the device from leaking. These seals wear out over time and are no longer able to serve their intended function.

A break in the protective shell cover that surrounds the garbage disposal is another probable culprit. Regardless of whether your disposal is leaking due to the case or an internal seal, you’ll need to replace it.

How To Fix It

If this is your problem, your options are pretty limited. Keep in mind that water and electricity aren’t exactly friends, so you’ll want to get this repaired as soon as possible.

Your only real solution is to purchase brand-new garbage disposal. You can expect the new disposal to last between 8 to 15 years, depending on the amount of use and the quality of the appliance.

Garbage Disposal Leak From Top

If your garbage disposal is leaking from the top, it’s possible that the issue isn’t with your disposal. The sink flange, which links to the mounting ring of your disposal unit, could be the source of the problem.

The flange is the visible component of your sink that surrounds the drain hole in the middle. Most flanges are sealed with a plumber’s putty (a clay-like sealer) to avoid leakage. Some disposals employ screws to tighten the flange in place, though this is not typical.

The plumber’s putty can wear out (or the screws can loosen) over time, and the sink flange can no longer make a watertight seal. Other plumbing repairs under the sink may cause the garbage disposal to be struck or dislodged, compromising the seal.

How To Fix It

Plumber’s putty is used to seal most garbage disposals. You’ll have to remove the garbage disposal, clean off the old putty, and then reseal it. Other disposals rely solely on a flange that is tightened and compressed using screws. Something may need to be replaced. In either case, if you don’t know what you’re doing, this can be a major job (it requires removing and replacing drain pipes as well).

Garbage Disposal Leaking From Side

When your garbage disposal leaks from the side, it’s usually the dishwasher drain or the main drain line that’s the source of the problem. In most circumstances, this is a reasonably simple repair that you can complete without the assistance of a plumber.

The garbage disposal is connected to two drain lines: a dishwashing drain and the main drain line. The smaller drain travels through the wall and links the dishwasher drain pipe to the dishwasher intake on the trash disposal, while the larger drain runs through the wall and connects the appliance to the sewer. Because not all disposal units use the dishwasher drain, if you don’t have one, you won’t have to worry about this issue and can instead concentrate on the main drain line.

How To Fix

Tighten or reseal the connections: A metal clamp connects your dishwasher to your garbage disposal. You can tighten this with a screwdriver to see if the leakage stops. The main drain line is screwed together and features an internal rubber gasket. It’s possible that the screws need to be tightened or the rubber gasket needs to be replaced.

The post Why Is My Garbage Disposal Leaking? appeared first on Roto-Rooter of Greeneville TN | Greeneville TN Plumbing Company.

[rotorootergreenevilletn]

Three Ways You Can Fix a Leaking Pipe

Most leaks in plumbing will be either at a joint or a solder connection, so if the leak is coming from an exposed pipe, you can check these points first. It’s worth bearing in mind as well that not all leaks are immediately visible. If there is water damage to surrounding plasterwork and woodwork, it may indicate a hidden leak inside an internal wall or ceiling.

Check For External Sources of Leaks Outside Your Home

Water pipes that run along the ground outside your property may also have developed a break without you noticing. So before assuming that any problem lies with your pipework, check for broken mains supply lines which feed your house by opening up manhole cover covers, especially if you live near them.

How to Fix a Leaky Pipe With Fiberglass Tape

A specific fiberglass tape can be used to repair a leak. This tape is made from the same material as reinforced fiberglass cloth and has a waterproof sealant embedded. It can fix leaks in pipes of up to 3/4 inch diameter (19mm) and should not be used on plastic or metalwork because it will adhere permanently.

If you have enough expertise, then this method may be an option for you. However, if you are unsure, you should leave this job to the professionals like us at Roto Rooter of Greeneville TN. We will come to your house and repair the leak for a reasonable price!

Epoxy Putty Pipe leak repair

This method is an excellent way to fix a pipe leak. This is because it adheres strongly and will not disintegrate when exposed to water. You can get epoxy putty at any hardware store, such as Home Depot or Ace Hardware. To use this method, apply a small amount of the epoxy putty directly over the hole in your plumbing pipes that is causing the leak. The amount applied should only be enough to cover up the hole – about a 1/4 inch layer is sufficient. After applying the epoxy, set something heavy on top of it (such as a brick) so that it remains in place while the glue hardens overnight.

This method works best for leaks around 3/8 inch or smaller in diameter on plastic. Larger leaks will need the epoxy putty to fill in a larger area. If applying this method to a leak on metal pipes, first wrap some plastic or tape around the pipe so that the epoxy does not contact it and cause corrosion.

Fixing a Larger Water Leak

If the leak is larger than 1/8 inch, pressure injection epoxy will have to be used. This method is more involved since you will need to cut out a section of damaged pipe for it to inject properly. After making sure that the water is turned off on both sides and any remaining water has drained from the system, apply some epoxy putty around two inches away (on either side) of where the leak occurred.

After applying a thick layer (about one-half inch or an inch), place something heavy over it overnight while it sets up. The next day, insert a piece of threaded pipe into each hole and use this as a plug until you can get someone out there with pressurized epoxy inject or to fix the problem for you.

If this method is not possible, use a simple hose clamp as a quick fix. After making sure that the water is turned off on both sides and any remaining water has drained from the system, place the hose clamp around two inches away (on either side) of where the leak occurred. The next day, tighten it down with pliers to create a tight seal until you can get someone out there with a pressurized epoxy injector to fix the problem for you.

This method is faster than doing it yourself and works most of the time, but it should only be used in small leaks or emergency situations since it does not adequately seal against future leakage.

Hire a Professional to Fix Your Pipes

Roto Rooter plumbers offer expert plumbing leak repair services for your pipes, fixtures, and plumbing system. We have the experience and knowledge to fix leaks around the home or business quickly.

If you are experiencing water leaks of any kind, contact Roto Rooter of Greeneville TN to schedule an appointment today.

The post Three Ways You Can Fix a Leaking Pipe appeared first on Roto-Rooter of Greeneville TN | Greeneville TN Plumbing Company.

[rotorootergreenevilletn]

How to Identify a Water Leak in Your Ceiling

Water leaks are quite common, and they are bound to happen in homes and buildings, especially as they get older. Some leaks are apparent and can be noticed easily, but others may not be as obvious; you may have to go the extra mile to identify those. Leaks in ceilings made of concrete are more challenging to locate because the concrete doesn’t readily absorb water. Once water leakage begins to surface, it indicates severe damage inside, and you must address it quickly. 

Water leaks in your ceiling are caused by either a roof leak or a plumbing leak.

Water Leaks Caused by a Roof Leak

A roof leak occurs when a hole in the roofing panel allows water from rain or other sources to seep in continuously. 

Water Leaks Caused by Plumbing 

A plumbing leak occurs when there is damage to the plumbing fixtures in your building, such as a rusted pipe, a loose-fitting, or a faulty faucet. 

Whatever the cause of the damage, water leaks should be fixed immediately they are noticed. In addition, we advise that you should regularly check on your building to see if there are any issues. 

Look out for the following signs when you are checking your building:

. 

Signs that Indicate Water Damage

Water Stains on Ceilings

If there is a dark spot or discoloration in your ceiling, there is most likely a water leak there. Most times, such leaks come from the roof. But if you have a bathroom upstairs above that spot on the ceiling, the leak is likely from the bathroom. This leak could be caused by a broken pipe, worn-out tap, a leaky toilet, or a bad bathroom sink. This sign only appears after the leak has been there for a long time; therefore, you should address it as soon as you notice it. 

Mold or Mildew 

They usually appear as a dark powdery growth on the ceiling or wall, and persistent water leaks cause it. Mold is a fungus that grows as a result of consistent moisture from damaged pipes. They can appear in different colors ranging from black to white, orange, green, or even purple. They reproduce by tiny, inconspicuous, lightweight spores. The spores can cause respiratory issues if inhaled. As the organism grows, it releases a gas that causes a musty odor that circulates that whole room. Experts should be contacted once the mold is noticed.  

Low Water Pressure 

If the water flow pressure through taps suddenly drops, especially if no other fixtures are in use, then there is a possibility that there is a water leak somewhere in the system. This can be caused by a build-up of sediment in the pipes and waterways or faulty valves, thus reducing the amount of water running through the pipes.

Sagging Ceilings

When your ceiling is sagging, it is often a result of a leaky roof or leaky pipe. It sometimes occurs with discoloration on the saggy part. Ceilings should be repaired immediately to prevent more severe and costly damages like a roof collapse. 

Peeling Paint or Wallpapers

If the paint on your ceiling starts blistering and flaking, it is an indication that there is a water leak in the ceiling or wall. Many times, this shows only after the leak has been there for a while and is often accompanied by discoloration of the affected part. It also requires immediate attention to prevent further damage.

Abnormal Water Bills

There is a high chance that there are water leaks in your ceiling if your water usage bills suddenly become higher than usual for no apparent reason. The US Environment Protection Agency usually recommends that homeowners check their water usage regularly. If a family of four exceeds 12,000 gallons of water per month, there are serious leaks in the house. 

Can Water Leaks be Avoided?

The use of quality and standard plumbing systems and fixtures can greatly reduce the chances of a water leak. But eventually, everything is subject to wear and tear. Therefore water leaks aren’t completely preventable. We advise that you should have periodic inspections on your plumbing systems. It could be monthly, bi-monthly, quarterly, or even yearly. The most important thing is that it should be regular. 

Don’t Ignore the Signs, Call Us at Roto Rooter of Greeneville TN

It’s really important to take plumbing leaks seriously no matter how small they seem. If left unchecked, it could cause serious damage to your building over time. Call us at Roto Rooter of Greeneville TN as soon as you notice any issues.

The post How to Identify a Water Leak in Your Ceiling appeared first on Roto-Rooter of Greeneville TN | Greeneville TN Plumbing Company.

[rotorootergreenevilletn]

Top Reasons to Call for an Emergency Plumber

Plumbing problems are common. Hence, an emergency plumbing service is a necessary service for homes and commercial properties. Some people however, think that they have to address the plumbing problems on their own immediately to avoid further damages. This approach in truth stems not only because of their fear for more damages alone but also the fact that they need to pay more if they call for an emergency plumber at the dead of the night. 

If you want to avoid spending more, it’s necessary for you to know which emergency plumbing problems have to be fixed by the professional right away and which problems can be fixed on your own. 

Figuring out your emergencies 

Below are some of the situations that call for immediate attention from plumbing professionals. 

Increased risk of flooding

There’s a need for professional’s help when there’s a possibility of flooding. There are several reasons for water overflow and this flooding can cause extreme damage to your home – the carpet, fixtures, furniture, building materials, hardwood floors, insulation, and more. The flood may also damage your electrical system. The aftermath of the flood isn’t only limited to the damages to your home’s interior but also to your finances and daily schedule as well. You need to put some time to do extensive cleaning. You can avoid all these expenses if you call the help of professional emergency plumbing service right away. 

Sewage issues

Any sewer problems should be taken care of right away not only because you want to save more and prevent needless expenses on repairs or replacement. You want to fix any sewage problems as soon as possible to keep your home safe from the diseases brought by the waste product in your sewage system. A backup sewer can lead to the spread of foul odor and infiltration of pathogens into your home. These things are health hazards. It won’t only disrupt the daily activities but it will also compromise the quality of water and air in your space. Whatever the cause of that sewage backup – may it be a broken or burst pipe, root tree intrusion, and others, you need to get the help of a professional immediately. 

You don’t have running water

Access to running water is critical to every household or any establishment. An emergency plumber should be called as soon as you are able when you don’t have water. It’s not typical for water to just stop running. There are several factors that have to be checked to determine what the issue is. You need water to clean the house, to cook, to take a bath, do your laundry, and many more. It’s not comfortable for anyone in the household if you suddenly don’t have any running water. 

Frozen pipes

This problem is common for homes located in areas with sub-zero temperature during the winter seasons. Frozen water expands and this causes problems in your plumbing system. It’s a usual cause for low water pressure or in worse cases, it can stop your water from running altogether. 

You need the help of the professionals to unfreeze the water and insulate your pipes. The process needs equipment that most households don’t have. 

No hot water coming out

It’s not wise to tackle hot water issues on your own because it requires a certain level of expertise both on the electrical and plumbing side of things. There are also several reasons why your water isn’t working, figuring out which one is causing the problem is a challenge for people without basic knowledge and experience. This problem isn’t much of a problem for some homes but it can be a real issue for homes with family members who go to work or go to school everyday. They need this system to work to begin their days! 

Call for an emergency Plumber today

Doin a do-it-yourself project on some issues in your home is not a problem. However, there are some problems that can’t be solved on your own. Some issues have to be dealt by the professionals. If you are looking at similar problems stated above then you need to call the help of emergency plumbing right away. Do not underestimate these problems to avoid needless expenses of bigger damages in the future. 

Pick highly-skilled and licensed plumbing contractors to take a look at the issues.

The post Top Reasons to Call for an Emergency Plumber appeared first on Roto-Rooter of Greeneville TN | Greeneville TN Plumbing Company.

[rotorootergreenevilletn]

Warning Signs for Slab Leaks to Look Out For

Slab leaks are some of the most common plumbing problems in many homes. The slab leaks are water leaks under the slabs of concrete in your home. The leaks aren’t a good sight to behold and most disturbing and frustrating. Slab leak detection is difficult to do because it happens underneath your floors. However, early slab leak detection is critical in the repair process. It helps to minimize the damages and it would help prevent needless expenses that could have been mitigated if you knew the warning signs to look out for. 

What is a slab leak?

Slab leaks are some of the hardest leaks to detect or fix. Most homeowners don’t notice the slab leaks for a long time until the problem becomes too much. The broken pipe underneath your floor causes the water to rise and seep into the ground of your home’s foundation. The leak will damage the concrete of your home and soil erosion around it. Eventually, the foundation will buckle and shift. Not long, you will end up with cracked floors and walls. In the worst case scenario, if the slab leaks go undetected for years, the portion of your house may even collapse. 

Slab leaks are common issues for homeowners but the frequency depends from region to region. Other states that are more prone to earthquakes and ground shifting causes ground cracks. Old homes are also more prone to slab leaks than newer homes because of their old copper pipes. 

When do you need Slab Leak Repair

Use this list as a guide for you to know if you need a slab leak repair or not. 

Hot spot on your home’s flooring

One of the basic slab leak detection methods is a persistent hot area of your floor. The warm area indicates that a hot water line is busted underneath your floor. 

Water coming out from the slab

A water coming out from your slab or from the ground is an obvious indication of slab leak. Call in the help of professional plumbers immediately if you spot water from your slab. 

Increased water bill 

As a homeowner, you have an idea of your monthly water bill. If all of a sudden, your water bill increases even when the water usage is the same, then there’s something wrong with your system. There is a possible leak in your water line and with a leak, that means that your water is running 24 hours a day until you fix the issue. If you can’t find the leak in any visible area, then the next explanation is a slab leak. The solution is a slab leak repair. 

Heaving foundation

Your foundation is heaving when there’s a swelling in your foundation slab. The swelling of your foundation can even lift your home slightly. This condition, or otherwise called as foundation heaving is another warning sign for slab leaks. If you see a significant shift in your home’s foundation then there’s no point of delay. You need to call for the professionals for a slab leak repair. 

Fixing the Slab Leak

Slab leak detection is one thing and slab leak repair is another. Doing the repair on your own isn’t a suggested method. It’s difficult and it’s costly. The best option is to seek out the help and services of a professional plumbing company that offers the services that you need – slab leak repair. The other downside of doing a slab leak repair on your own is the risk of ripping your floors and ending up destroying the wrong area. Since it’s difficult to spot slab leaks, there’s a high chance that you’re going to miss the exact location of the leak. 

Call for backup

If you’re unsure, you need to reach out to a service provider to help you with your slab leaks. Do not worry much about the cost because when things become worse, that cost you were going to pay for the repair will double in amount. Entrust the slab leak repair to the professional who have been trained for the job and who already have years of experience with it. You are more assured when you put your trust to a licensed and insured team of contractors. 

Reach out to a professional service provider today.

The post Warning Signs for Slab Leaks to Look Out For appeared first on Roto-Rooter of Greeneville TN | Greeneville TN Plumbing Company.

[rotorootergreenevilletn]

Top 5 Reasons for Water Leaks in Houses to Look Out For

There can be several reasons for leaks. The truth is, water leaks are one of the worse problems that homeowners face. Year after year, an average home loses about 2,000 to 20,000 gallons of water due to leaks. That water loss leads to a significant waste of money. Some water leaks are easier to discover such as dripping faucets and showerheads while others can go undetected for years. Without proper and regular pipe inspection, you may not know that you have leaks in your pipes that’s been going on for months. 

The easiest way to detect water leaks is by using your water meter. Your first need to turn off all the water inside and outside your home. Take note of the water usage in the meter before the test. If the meter keeps on turning and adding on water usage, then you’ve got yourself a leak. The difficult part is determining where the leak is coming from.  You can call in the help of the professionals. Roto-Rooter has a team of experienced and expert plumbers. They’re locals of the community and they have seen almost, if not all, of the water leaks and issues there are. 

However, you can also go down and personal with your own home. Look at these top five reasons for water leaks in houses and check if your home has the same problems. 

Check Your Faucets

This may sound trivial to you but most times, the water leak is coming from one of the faucets in your home. A worn rubber washer found underneath the handle is the usual cause for faucet leak. Use the right tool to replace the washer. Do not forget to turn off the water under the sink or at the main cutoff valve. Gain access to the gasket by removing the faucet handles. You can check out your city’s Home Depot or other hardware stores for the tools that you need. 

Check for Shower and Tub leaks

Aside from the faucet, shower and tub leaks are other common sources of water leaks. Check you showerheads and toilet faucets. These aren’t major leaks but could still contribute to water and money loss if taken for granted. If you decide to do a do-it-yourself repair, make sure to determine the type of faucet you have first. The kind of repair you do depends on the kind of faucet you have. For bathtubs, drain leaks are the most common and they happen when the drain-trap piping is loose. 

Do a Visual Check-up

Leaks coming from the pipes inside your walls and ceilings are difficult to assess. They could go unnoticed for a long time. A visual inspection will help you check if there are leaks in your pipes. Do a closer look at your walls and ceilings in every room. Check the walls for staining and discoloration, this is a common sign for hidden leaks. Check for molds and strange dips on your ceilings or walls too. The water damage often stretches out your material, eventually the pressure causes the caving in of some part of others peoples’ homes. 

Check the water pressure

For homes near fire hydrants or homes located in hills and tall buildings usually have high water pressure. The average water pressure is only at 60 per square inch and the home plumbing is typically designed to withstand a maximum pressure of 80 per square inch. Water pressure is out of your control so if you think you do have a high water pressure in your home, you need to talk to your plumber on the ways to regulate your home’s water pressure. 

Is it time to call a plumber to fix my leak? That’s a question that many homeowners ask themselves often. Certain leaks can’t be fixed on your own even when you have the tools. Sometimes, it takes experience to know how to fix certain water leak problems. Don’t always take the fixing on your own hand, let the experts have a go at it as well. 

With water leaks, call the professionals whom you can trust. Roto-Rooters has a team or experienced and licensed plumbers you can depend on for a prompt and reliable water leak repair.

The post Top 5 Reasons for Water Leaks in Houses to Look Out For appeared first on Roto-Rooter of Greeneville TN | Greeneville TN Plumbing Company.

[rotorootergreenevilletn]

Causes of Overflowing Toilet and How to Fix It

An overflowing toilet is a common problem among households. There is no cause for panic when you’re experiencing such a situation. Keep a level head and know that you can manage an overflowing toilet without making a mess of your bathroom. Stopping the flow is often the first step in dealing with an overflowing toilet. It’s also essential to identify the underlying cause of the problem to prevent the same issue in the future. 

The primary way of stopping an overflow

When there’s an overflow, the most logical action is to stop the water. Here are three ways to do so. 

Close the flapper in the toilet tank

Take off the toilet tank’s lid and look for a flapper at the base of the tank. The flapper is the one that covers the opening of the toilet bowl. Push the flapper down to stop the water from getting from the tank and getting into the bowl. 

Lift the float n the tank

The float controls the flow of water into your tank. Lift the float to shut off the water. 

Turn off the water valve.

The valve controls the toilet’s water flow and is usually found at the base of the toilet. Turn the valve off to turn the water flowing into the toilet. Turning the valve is a bit more challenging than the other two, so do it as a last resort. The water in the toilet will slowly go down after turning the valve off.  

Causes of Overflowing Toilet

Overflowing toilet happens because of several reasons. Here are typical causes for the overflows. 

Clogged pipes

Clogs in your toilet and connecting pipes stop the water from flushing out thoroughly. Clogs are often caused by flushed toilet paper, wipes, diapers, sanitary products, Q-tips, etc. Try to flush the toilet repeatedly, and if that doesn’t solve it, you can use a plunger to remove the clog. However, if the plunger is still not working out, it’s time for you to call a professional to remove the clog. 

You need to turn off the water supply and remove the water as soon as you spot the clogging issue. It would keep the water from soaking in your floor and drywall. Dry down the area and make sure to disinfect the places where the toilet water reached. The water from the toilet may have harmful bacteria and give off a foul odor, so make sure to thoroughly clean and disinfect.

Low Flow Toilets

Newer homes today use low toilets with the goals of conserving water and maximizing water usage. The downside of a low water toilet is that it’s not effective in flushing everything down. 

Blocked vents

A blocked vent is another cause for an overflowing toilet. The plumbing vent is a vertical pipe connecting all the plumbing fixtures. The vents allow air to enter through the pipe and replace the air that goes down whenever the toilet is flushed. Debris and other dirt in the vent stops or slows down the draining process. It also causes bad smells and bubbling sound whenever your flushing. There may be no overflow, but the foul smell and the slow drain are enough reasons for you to take action. If taken for granted, the blocked vents may damage the pipes. 

Cleaning vents is a challenge, so most homeowners prefer to help a professional remove the debris safely and adequately. They have the k knowledge and the right equipment to handle the job right the first time. 

Full Septic Tank

Some houses use a septic tank and not a municipal sewer system. The septic tank keeps all the waste and releases the excess water into the surrounding drain field. When the tank is full, the water just escapes, and the toilet overflows. Regular maintenance is necessary to see the level of your septic tank. It allows you to gauge when you need to replace it or repair it. 

If your toilet is still clogged even when you already turned the valve off, it’s high time to contact a professional plumber near you. It’s best to act fast to keep the overflow to a minimum and ensure that no further damage occurs.

The post Causes of Overflowing Toilet and How to Fix It appeared first on Roto-Rooter of Greeneville TN | Greeneville TN Plumbing Company.

[rotorootergreenevilletn]

Common Causes of Sewage Backup and How to Prevent Them

Sewage backup can happen to anyone at any given time. It is one of the most common water damage disasters that homeowners have to deal with. Sewage backup doesn’t only damage your home. It can also be hazardous for your family’s health as sewage has chemical and biological contaminants. 

Health dangers from sewage backup

Take immediate actions to prevent illnesses caused by sewage backup. The dirty water can seep into one’s body via open wounds and may cause Hepatitis A, Rotavirus, E.Coli, among others. Backup sewage can also worsen conditions such as asthma and other allergies. That aside, the dirty water can also cause mold growth inside your home. 

There can be many reasons why this backup happens. Here are the common causes of sewage backup and some preventive measures you can do to protect your home from such water damage. 

Causes of Sewage backup 

Sewer backups don’t cause most water problems. Most often than not, it happens because of damages in the city’s main sewer line, your home sewer line, or both. There are, however, more to it than that. 

Tree Roots 

Trees and shrubs look for moisture and make their way in to sewer line cracks and pipe joints. These tree roots can create damages to homes’ sewer lines as they grow bigger. They grow in pipes causing holes and blockages, and they can wrap around your sewer line and crush your pipes. If the city tree is responsible for the sewage backup, you can contact your plumber to alert the local government and fix it. 

Cracked Sewer Lines 

Cast iron, cement, and clay are the common materials for old homes’ sewer lines. These materials can break over time and thus cause sewer damage. Most residential properties today, however, use PVC, clay, or Orangeburg for their sewer lines. These materials are more durable, and they last for a far longer time. Still, you can’t expect them to remain forever. In time, these materials will eventually break and crack. 

Old sewer system 

The American Society of Civil Engineers reported that the country’s miles of sewer lines are on average more than thirty years old. The number of homes in the United States is rapidly increasing, and the aging sewer system is no longer equipped to manage the demand. This aging sewer system is also one of the reasons for many flooded basements and overflows. 

Clogged Sewer Lines

We often take drains for granted and drain everything down the pipe: fast food wastes, hairs, oil, wipes, and more. We flush them right down and don’t look back. These things can cause clogs and eventually lead to sewage backup. 

Prevent Sewage backup 

There are several ways to prevent sewer problems in your homes. 

1. Proper garbage disposal

It may sound easy, but sometimes, we still need to be reminded. Dispose of the trash properly to avoid clogs in your sewer lines. Don’t throw everything or pour down everything in your drain, especially grease or cooking oil. The grease/oil cools off and solidifies in the drain causing the clog. Items such as paper towels, tissues, wipes, and cloth diapers take a long time to disintegrate. These things don’t belong to the drain. Putting drain traps is helpful to catch that food waste and other solid objects. 

2. Put up a backwater prevention valve

Some homeowners invest in a backwater valve and install one in their basement. The backwater valve lets sewage go out but not back in. It can be your final line of defense in case of sewage backups. 

3. Proper drain maintenance 

Clean the drains regularly. Don’t just use chemical drain cleaners. Use baking soda, white vinegar, and warm water to flush your drain monthly. 

4. Schedule an inspection 

It may be hard to spot the signs of sewer backups in your home if you can hire a professional plumbing contractor to conduct a thorough inspection of your sewer line. They are trained to identify the water damage signs before it happens. They can also make recommendations about the changes you can make to prevent sewage backups. 

Roto-Rooter is a Plumbing and Drain Service provider that makes sure that your pipes and your plumbing system are working correctly. Give us a call, and our team of professional plumbers is ready to help you with your water system and plumbing issues. 

The post Common Causes of Sewage Backup and How to Prevent Them appeared first on Roto-Rooter of Greeneville TN | Greeneville TN Plumbing Company.

[rotorootergreenevilletn]

Drain Maintenance: A How-to Tutorial

The drain system is one of the most overlooked structures inside our houses. This system usually stays invisible until a problem surfaces. Although it looks to be simply a series of connected pipes, it is actually a complexly designed system that provides seals to prevent sewer gases from penetrating our homes. Other than that, it also helps in removing solid and liquid wastes. Because of this, it is imperative to perform regular drain maintenance. A badly-maintained drain can eventually lead to clogs and blockages, which is a huge hassle to sort out. By keeping your gutters clean and well-functioning, it will surely go a long way towards guaranteeing the health and performance of your home’s overall plumbing efficiency. In this post, we will provide you with practical advice and tips on essential drain maintenance that will maintain the smooth water flow in your kitchen, bathroom, and pipes inside your home. We will also include tutorials on what to do if your drains need a clean-out. Here we have gathered the necessary information that you need to know to keep your drains healthy, so have a look:

Know the Materials to Avoid Putting Down in the Drain

One of the most basic methods in drain maintenance is to remember that prevention is better than cure. True to this saying, it is preferably better to learn about what you should not put down in the drain to avoid blockage. This is very important. The materials that should never be put down in a drain are liquid fats, oils, or grease. As these materials cool down, they become solid, which then clings to the pipes’ insides, turning into a clog-inducing paste. Other than that, you should also avoid putting in certain materials such as eggshells because the edges of eggshells catch on other items, which later grow into larger clogs. Coffee grounds are also a no-no because they tend to stick in pipe walls. They then build into a paste when crammed into small areas, which causes further blockage. You should pay more attention to the everyday routines that might threaten the health of your drains. These activities include rinsing pans and plates, hair washing, and emptying coffee grounds down the plughole.

Invest in a Good Drain Guard

Using a drain guard on all your plug holes can dramatically lessen the amount of waste that is getting washed down in your sink. As we know, drain guards are small, plastic or metal grate-like disks that sit atop your plug that catch debris and smaller food scraps, which you can manually remove and throw into the garbage. This magical little device plays a significant role in your drain maintenance. Other than that, you can also install a drain guard for your shower to catch the loose hair and other scraps that can wash down the drains after taking a bath.

Clean Your Drains

Drain maintenance is actually something that you can do every day. So before you get started cleaning your drains, it’s best to prepare the necessary tools and materials you need during the drain maintenance. Some of these may include baking powder, white vinegar, soda crystals, cleaning chemicals, protective gloves, and goggles. An excellent way to clean your pipes is to pour hot water down a household drain. Then you can follow it up with some cool water to flush out the clogs that were melted away by the hot water. Alternatively, you can also use baking soda and vinegar. You can try to pour half a cup of baking soda down your drain, and then followed by half a cup of vinegar, plug the sink and let it sit overnight. You can then flush the gutters with hot water in the morning and see the results.

Yes, it is true that sometimes, drain maintenance can be a hassle, but it is a vital part of keeping the drains and public sewer systems clean and clear of any stubborn blockages. Knowing the proper ways of drain maintenance can surely save more time and money, which you can use for more essential matters.

The post Drain Maintenance: A How-to Tutorial appeared first on Roto-Rooter of Greeneville TN | Greeneville TN Plumbing Company.

[rotorootergreenevilletn]

10 Plumbing Ideas Everyone Needs To Learn

Are you currently handling a leaking faucet, reduced water pressure, or plugged water pipe? You’re probably inclined to get in touch with a professional local plumber, together with good reason. Property owners usually don’t have the required abilities for DIY plumbing related work. They may even make the problem worse in the end, resulting in losing thousands of dollars in house and personal damage. But don’t put your local plumber on the speed dial yet! Listed below are ten standard plumbing related secrets every homeowner should know. Possibly one of these brilliant ideas could save you a costly repair from your local expert. 

Know the Place of Shut-Off Valves

Before you move into a brand new property, be aware of the principal shut-off valve’s positioning and drain (occasionally, you can find the shut-off outside of the home). You need to get familiar with sewer line access points in case you have to execute regular cleanouts. Note that flats and condominiums may not have their very own specialized close-off valves.

Don’t Puncture Waterlines

Have you been about to drill holes or pound nails to your surfaces, flooring, or roof? Initially, see whether you can find any supply or drainage plumbing behind your work location because you don’t wish to rupture them accidentally. You might be able to track down plumbing behind surfaces having a low-cost stud finder. Otherwise, you might purchase an endoscopic video camera that you can snake in the covers. 

Figure Out What’s Flushable

Homeowners shouldn’t use their potty like a garbage can, given that flushing anything except toilet paper leads to nasty clogs. Flushable baby wipes can also ruin the system! 

Don’t Place Garbage Down the sink

Never put coffee grounds, food trash, bacon grease, vegetable peelings, or starchy foods like rice or potatoes along with the cooking area strain. They may undoubtedly clog your pipes. It’s also wise to read the manufacturer’s manual to understand what precisely your machine is made for.

Consider the Plunge 

Buy a substantial-high quality plunger to get rid of clogs in toilets, kitchen sinks, and drain pipes. If you intend to thoroughly clean kitchen sink traps, utilize a plunger to push most of the water out before taking off the snare. The work might be a good deal much less moist and untidy.

Grab the Vacuum 

When you’re attempting to dislodge a clog, the result of a tiny, challenging object (such as a child’s plaything, toothbrush, or hair comb) depends upon a moist-dried out vacuum. It’s more effective to suck the matter out. A plunger will only push it further in the drain, which makes it more challenging to remove. 

Don’t Overlook Water leaks

That regular drip, drip, drip of any fittings represent funds moving down the drain. In reality, a leaky sink typically wastes materials approximately eight gallons of water per day, while a running bathroom can waste materials 200 gallons per day. Resolve tiny spills promptly before they turn out to be significant—and costly—problems. 

Never Over-Firm up Fittings

A standard DIY domestic plumbing error has over-tightening fittings and connections, which leads to shattered mounting bolts and removed screws. Consider this saying: “hand-tight is simply enough.” 

Get Acquainted With Plumber’s Tape 

Plumber’s tape (otherwise known as Teflon tape) can be used to seal tubing threads to avoid spills around joints and fittings. It would be best if you typically wrapped plumber’s tape thrice throughout the tubing threads before closing. Also, note that white-colored tape is made for typical home domestic plumbing assignments, while yellow-colored is made for gas series connections. 

Check for Water leaks 

After every domestic plumbing project, look for spills by running water through closing and opening all valves and drains. Even professional plumbing contractors may miss a tiny drip and require a reseal connection.

The post 10 Plumbing Ideas Everyone Needs To Learn appeared first on Roto-Rooter of Greeneville TN | Greeneville TN Plumbing Company.