atsthermal

[atsthermal]

Anemometer for Thermal Characterizations of Electronic Packages

The ATVS-NxT scans up to 32 sensors to read air velocity and temperature. Temperature and airflow measurements range from –30° to 150°C and 0 to 51 m/s. Characterize heat sinks, PCBs and racks. @Mouser https://www.qats.com/Products/Instruments/Temperature-and-Velocity-Measurement/iQ-200

[atsthermal]

Vapor Chamber-base CPU Cooler Maximizes Cooling

quadFLOW CPU coolers take in air from four horizontal sides. They cool hot components in dense PCBs with restricted air flow. Vapor chamber base units maximize heat spreading for extreme cooling needs. @Mouser https://www.qats.com/eShop.aspx?q=Ultra-Cool%20High-Power%20Device%20Coolers

[atsthermal]

Extruded Aluminum Heat Sinks

Extruded aluminum heat sinks in bar lengths of 300mm (11.8in) provide cut-to-length cost-saving cooling solutions. Multiple components can be cooled with machined lengths from the same extruded bar. @ Digi-key https://www.qats.com/eShop.aspx?productGroup=0&subGroup=0&group=All&q=Profile

[atsthermal]

Leak Detectors Shut Off Valves

The Automatic Shut Off Valve detects water leaks and shuts off a valve in a piping system. Water flow is stopped, and a beep signal indicates the leak. It can be used in filtration and other water flow systems. @Sager https://www.qats.com/Products/Liquid-Cooling/Leak-Detector/ATS-LD-14

[atsthermal]

Heat Pipe Bending Tools

ATS Heat Pipe Bending Tools let users apply the right leverage and torque for reproducible 10–170-degree bends in round profile pipes. The tools prevent over bending which lowers a heat pipe’s thermal performance. @Digi-key https://www.qats.com/Products/Heat-Pipes/Heat-Pipe-Bending-Tool

[atsthermal]

iQ-200 Measures Temperature, Velocity & Pressure Together

The iQ-200 measures material and air temperatures, air velocity and pressure at multiple points. Easily test and characterize heat sinks, PCBs and card racks, without multiple systems and s/w. @Mouser https://www.qats.com/Products/Instruments/Temperature-and-Velocity-Measurement/iQ-200

[atsthermal]

Liquid cold plates cool IGBT modules, lasers, motor devices, automotive components and more. Provide 30% better cooling than other cold plates. More surface area maximizes heat transfer. Very uniform surface temperature. @Sager https://www.qats.com/Products/Liquid-Cooling/Cold-Plates

[atsthermal]

Power Brick Heat Sinks

ATS power brick heat sinks cool eighth, quarter, half and full brick size DC-DC converters. Feature maxiFLOW heat sink design, with less pressure drop and more surface area to maximize cooling. Available @Mouser https://www.qats.com/eShop.aspx?productGroup=0&subGroup=2&q=Power%20Brick

[atsthermal]

Liquid Crystal Thermography System

The tvLYT is a high-resolution liquid crystal thermography system for low cost, accurate temperature measurement of hot spots on PCBs, micro circuits, ICs and modules. Features a solid-state color camera, LED lighting. https://www.qats.com/Products/Instruments/Surface-Thermography/tvLYT

[atsthermal]

Aluminum Stamped Heat Sinks

Stamped aluminum heat sinks bring low-cost cooling to power transistors, diodes, MOFSETs, regulators and other components. Attach using solder, clips or screws and nuts. Added TIMs optimize heat transfer. @Digi-Key https://www.qats.com/eShop.aspx?productGroup=0&subGroup=2&q=Stamp

[atsthermal]

Benchtop Wind Tunnel

The BWT-104 open loop, benchtop wind tunnel thermally characterizes components, PCBs, heat sinks and exchangers and cold plates. The wind tunnel provides uniform, homogeneous airflow up to 4 m/s (800 ft/min). https://www.qats.com/Products/Wind-Tunnels/Open-Loop-Wind-Tunnels/BWT-104

[atsthermal]

Thermal requirements, PCB layouts, and system designs may need custom, liquid cooling solutions. ATS can design and manufacture Custom Cold Plates for cooling hot components including IGBT modules and high-powered semiconductors. https://www.qats.com/Consulting/Liquid-Cooling-System-Design

[atsthermal]

LGA Heat Sinks

ATS-57000 LGA heat sinks provide the highest cooling performance for Intel, Freescale, AMD and other manufacturers’ multicore processors. Active and passive versions available. Secure push pin mounting. @digikey https://www.qats.com/eShop.aspx?productGroup=0&subGroup=0&group=All&q=LGA#

[atsthermal]

High Precision Water Flow Meters

ATS Flow Meters measure volumetric flow rate of water in a pipe. Compact, economical, and extremely accurate, they automatically turn on when there is flow rate and shut off at no flow. Available @mouserelec https://www.qats.com/Products/Liquid-Cooling/Flow-Meter

[atsthermal]

Straight Fin Heat Sinks with superGRIP Attachment

For economical and secure cooling of a wide range of BGA components, ATS provides straight fin heat sinks with the superGRIP attachment system. The superGRIP frame and clip system takes minimal space on dense PCBs. @digikey https://www.qats.com/eShop.aspx?q=Straight%20Fin/superGRIP

[atsthermal]

Closed Loop Wind Tunnel for Thermal Studies

The CLWT-067 closed loop wind tunnel thermally characterizes PCB components and can be used to calibrate sensors. It provides airflows to 7 m/s in controllable temperatures from ambient to 85°C. @mouserelec https://www.qats.com/Products/Wind-Tunnels/Closed-Loop-Wind-Tunnels/CLWT-067

[atsthermal]

Fluid Chiller and Heater System

The TEChill-1400A chiller and heater system provides precision heating and cooling of a fluid medium, e.g., in attached cold plates. It has no moving parts, eliminating issues with vapor compression. See @mouserelec. https://www.qats.com/Products/Liquid-Cooling/Chillers/TEChill-1400A